1 / 14
The Tower - Modular Desktop Organizer — zdjęcie 1
1 / 14

The Tower - Modular Desktop Organizer

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

The Tower is a Rail-Based modular desk organizer that uses modules that slide into the base or extension pieces.

Ocena
0 / 5
Polubienia
4
Pobrania
5
Wydruki
0
Wyświetlenia
122
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Organizers
Licencja
Creative Commons — Attribution — Share Alike

The Tower is an extendable, modular desk organizer that uses a rail based system to attach modules to the base, or an extension piece. It comes with 8 different modules that I designed: A Phone Holder, Lego Display Board,  Hook (I use it for controllers), Cupholder, Battery Organizer, Cable Spool, a USB/SD card organizer and a pull-out shelf. If you want to create your own modules, look below for the specs.

                                                      MODULES

Phone Holder - Basic Phone holder with a hole on the bottom

Hook - A hook you can use to hang stuff off of, or if you're feeling brave, you can even fit an (upside down) controller in it!

Cupholder - 7.4cm diameter and a standard can fits pretty well. 

Battery Organizer - This can sort out AA and AAA batteries, just remember to put them in the small hole on the top, not the big one. This one is a bit of a W.I.P, because it does jam sometimes but it's open design doesn't make it big of a deal. (The Adapter Piece is needed for this to slot into the base and this is meant to be at the bottom) Prints on it's side

Cable Spool - This prints in 2 parts which just screw together. 

USB/SD Card Organizer - This module can hold up to 21 USB drives, 7 Full Size SD Cards and 16 Micro SD Cards. There is also a little slot below the USBs which has a curved bottom where you can put a stylus or really anything you want in it. (This module is meant to be at the bottom because of the SD card bridge)

Lego Display Board - This module has slots for up to 3 Minifigures at the top, and 2 other slots where you can put the plates in. 

Pull-Out Shelf - This module is made up of 3 different parts, the inside which is the actual shelving, the outside which has the dovetails and the rails on the inside for the shelves to slide into, and the pegs which just slot into the shelf. Make sure the circles on the pegs are closest to the back wall. This one is a W.I.P, and while still functional, it isn't perfect. (Also meant for the bottom)

Plain Module - Blank module ready for you to modify!  

                                       DESIGN SPECIFICATIONS 

  • Standard rail height (Also the height for the extension piece not including the pegs) is 110mm. The profile can be found below

  • The base measures 150x150x125mm (Not including the pegs), which is the height of the extension piece and the plate combined. All extension, plate pieces and the double height base share the same 150x150 measurement.

  • The inside of the base and extension pieces are 118x118, with 5mm fillets. The outsides on the plate, extension and base pieces also have 5mm fillets on the corners

Female Part of rail profile sketch. For my modules, I offset this by 0.8mm, than added a .5 fillet on the smaller side's edge because it was sharp. A premade plain module is available for download, if you don't want to go through the hassle. 

Peg Profile

The pegs are 10mm in diameter and have a 2mm fillet on both the top, and bottom. They extend out 10mm. They are 7mm away from the corners on either side. 

The holes are 10.5mm in diameter and are 14mm deep. They also have 2mm fillets at the bottom of the hole and the outside of it. 

This should be all the information you need to start creating your own modules!

If I left anything out, feel free to add a comment or message me. 

P.S. If this gets popular enough, I'l figure out how to actually do proper mechanical drawings

Tagi