1 / 3
Ultrasonic Slide‑Cleaning Carousel (25 mm × 25 mm Slides) — zdjęcie 1
1 / 3

Ultrasonic Slide‑Cleaning Carousel (25 mm × 25 mm Slides)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Solvent‑resistant ultrasonic carousel for cleaning 25×25 mm slides with angled slots and a beaker‑friendly design.

Ocena
0 / 5
Polubienia
3
Pobrania
5
Wydruki
0
Wyświetlenia
100
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

🧪 Ultrasonic Slide‑Cleaning Carousel (25 mm × 25 mm Slides)

A solvent‑resistant 3D‑printed carousel for cleaning small microscope slides in an ultrasonic bath.

Summary

This project is a circular slide‑cleaning carousel designed to hold 25 mm × 25 mm slides at a slight angle for efficient ultrasonic cleaning. The carousel sits inside a matching container with a snap‑on cover, and a central shaft keeps the carousel safely elevated above the bottom of the ultrasonic tank.

All parts are optimized for Nylon or other solvent‑resistant filaments, and the carousel + shaft are intended to be printed at 100% infill to avoid internal voids where solvent could accumulate.


📦 Included Parts

  • Carousel (rack) — circular holder for multiple 25×25 mm slides, angled for better cavitation exposure

  • Shaft — inserts into the center of the carousel to keep it raised off the tank bottom

  • Container — storage box for holding the rack after cleaning

  • Container Lid — protects slides from dust during drying or storage


🧼 Intended Use

This system is designed for:

  • Cleaning small microscope slides

  • Solvent‑based cleaning workflows

  • Ultrasonic baths where direct contact with the tank bottom must be avoided

  • Safe handling and storage of cleaned slides

The angled geometry improves solvent flow and cavitation access to both faces of each slide.


🧁 Optional Solvent‑Saving Setup

The carousel can also be placed inside a borosilicate glass beaker (minimum 70 mm inner diameter) and then placed into the ultrasonic bath. This reduces the amount of solvent required while still allowing strong ultrasonic coupling through the beaker walls.

🖨 Printing Recommendations

Filament

  • Nylon (PA12, PA6, PA‑CF) — best chemical resistance

  • Polypropylene (PP) — excellent solvent resistance if your printer supports it

  • PETG — acceptable for mild detergents, not recommended for strong solvents

  • Avoid PLA/ABS for solvent exposure

Print Settings

  • Carousel: 100% infill (prevents solvent pockets)

  • Shaft: 100% infill (strength + no voids)

  • Container + Lid: 20–40% infill is fine

  • Layer height: 0.2 mm

  • Perimeters: 3–4

  • Supports: Not required for most orientations

  • Bed adhesion: Nylon benefits from glue stick or Garolite


🛁 Cleaning Procedure

  1. Wash slides with dish soap
    Use nitrile gloves to avoid fingerprints and for safer handling.

  2. Rinse thoroughly with water
    Remove all soap residue.

  3. Load slides into the carousel
    The angled slots keep them separated and fully exposed to cavitation.

  4. Place the carousel into the ultrasonic bath
    Insert the shaft into the center hole first so the carousel stays elevated and never touches the tank bottom.

  5. Run the ultrasonic cleaning cycle
    Use your preferred solvent or detergent solution.

  6. Remove the carousel and transfer it to the storage container
    The container keeps slides clean while drying or waiting for the next processing step.


🛠 Design Notes

  • The shaft ensures safe clearance from the ultrasonic transducers.

  • The carousel’s open geometry allows free solvent flow and avoids cavitation dead zones.

  • Nylon construction prevents chemical attack from common slide‑cleaning solvents.

  • 100% infill eliminates internal cavities where solvent could become trapped.


Tagi