1 / 3
Dampfventilgehäuse  / Steam valve housing Jura Subito 630 Type 968 — zdjęcie 1
1 / 3

Dampfventilgehäuse / Steam valve housing Jura Subito 630 Type 968

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A 3D model of the Jura Subito valve operated by the coffee/water/Steam selection lever which gets leaky sooner or later.

Ocena
0 / 5
Polubienia
1
Pobrania
5
Wydruki
0
Wyświetlenia
53
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Kitchen
Licencja
Creative Commons — Attribution

-- for english please scroll down --

Ein detailliertes nachkonstruiertes Modell des Dampfventilgehäuses der Jura Subito. Das Ventil, das eine Schwachstelle dieser Kaffeemaschine ist (entweder der Kunststoff wird bröselig oder Kalk unterwandert die Membran, woraufhin das Ventil undicht wird), kriegt man schon seit Jahren nicht mehr. Ich habe es noch nicht gedruckt, sondern nur für den Fall nachkonstruiert, daß mein Reparaturversuch des originalen Gehäuses erfolglos bleibt.

Achtung: auf einem normalen FDM-Drucker wird man das meines Erachtens nicht fertigen können, man muß es lasersintern (lassen)! Außerdem muß das Material verklebbar, lebensmittelecht sowie resistent gegen heißen Dampf und kochendes Wasser sein!

Um das Gehäuse zu komplettieren, benötigt man das alte Ventil. Erst den aufgeclipsten Ventilhebel durch vorsichtiges Aufhebeln der drei Rastnasen mit einem Schraubendreher entfernen, dann den Stößel herausziehen. Nun kann man die Klebeverbindung durch Zusammendrücken des Ventildeckels in einem Schraubstock lösen (siehe Bild - vorsichtig zusammendrücken, bis es knackt, lösen, etwas weiterdrehen, wieder zusammendrücken etc, bis man den Deckel herausbekommt) und dann die Ventilmembran entnehmen.

Zum Montieren die Membran in das Gehäuse einlegen. Dann die kleine Stufe in der Bohrung des Gehäuses mit etwas Sekundenkleber einstreichen, den Deckel aufsetzen (Alle Nasen müssen in ihren Schlitz greifen -der Deckel hat nur eine korrekte Position) und umgehend kräftig zusammenpressen(!), bis der Kleber trocken ist. Erst durch das Zusammenpressen während des Aushärtens wird das Ventil dicht!

---

A detailed reverse-enginered model of the steam valve housing for the Jura Subito. The valve, which is a weak point in this coffee machine (either the plastic becomes brittle or limescale builds up behind the membrane, causing the valve to leak), has been unavailable for years. I did not get a print of it yet but rather made the 3D model for the case that my repair attempt of the original case will fail.

Please note: IMO you most likely won’t be able to print this on a standard FDM printer, you need get it printed with an SLS printer! Furthermore, the material must be bondable, food-safe and resistant to hot steam and boiling water!

To complete the housing, you will need the old valve. First, remove the clipped-on valve lever by carefully prying up the three locking tabs with a screwdriver, then pull out the pin element. You can now break the adhesive by squeezing the valve cover in a vice (see picture - squeeze gently until it clicks, release, turn it a little further, squeeze again, etc., until you can remove the cover) and then remove the valve diaphragm.

For assembly, place the diaphragm into the housing. Then apply a small amount of superglue to the small step inside the housing’s bore, settle the cover on top (take care to place the noses into the slots - the lid has just one correct position) and press firmly together immediately(!) until the glue has dried. The valve will only seal properly if has been pressed together while the glue is curing!

Tagi