LayersFactory
Zgłoś model
1 / 1
Ender 3 V3 KE Nozzle Wiper — zdjęcie 1

Ender 3 V3 KE Nozzle Wiper

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

dipindi

dipindi

@dipindi_3240654

Nozzle wiper with PTFE tube for Ender 3 V3 KE

Ocena
0 / 5
Polubienia
10
Pobrania
30
Wydruki
0
Wyświetlenia
319
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Creality Parts & Upgrades
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike
SzczegółyPliki (3)Wydruki i komentarze (Wydruki: 0) (Komentarze: 2)Remiksy (0)Kolekcje (7)Powiązane

Materials:

  • 1x M3 6mm (I used a thin flat head)

  • ~8mm PTFE tube

  • A1 Silicon Brush (cut to 16mm or 6 studs)

  • M4 nut (i used a square nut)

Assembly:

  1. Cut the silicon brush down to 16mm or 6 studs and stick it as shown on the images

  2. Screw in the PTFE tube make sure it is flush with the silicon brush

  3. Mount the wiper to the lower left corner and secure it using the M4 nut.

  4. Mount the bucket holder to the left side gantry and attach the cable

G-code:

DISCLAIMER:

⚠ TEST THESE VALUES BEFORE USE. I AM NOT LIABLE FOR ANY DAMAGE CAUSED TO YOUR HARDWARE. USE AT YOUR OWN RISK. ⚠

Start G-code (no wait bed leveling + flicker wipe)
M220 S100 ; Reset Feedrate
M221 S100 ; Reset Flowrate
; Heat bed
M140 S[bed_temperature_initial_layer_single] ; Set bed temp (no wait)
M104 S0 ; Keep nozzle cold


G28 ; Home axes
G29 ; Full bed leveling


; Move to purge start position safely
G0 Z10 F5000 ; Raise nozzle to safe height
G0 X-10.7 Y25 F6000 ; Move to purge XY position
G0 Z+3 F5000 ; Lower nozzle to starting purge height


; Wait for bed temp, then heat nozzle
M190 S[bed_temperature_initial_layer_single] ; Wait for bed temp
M104 S[nozzle_temperature_initial_layer] ; Start nozzle heating
M109 S[nozzle_temperature_initial_layer] ; Wait for nozzle to reach temp


; Purge filament
G92 E0 ; Reset extruder
G1 E25 F300 ; Extrude 25mm slowly
M400


; Blast blower fans for 10s
M106 P0 S255
G4 P20000
M106 P0 S0


G0 Y18 Z-1 F6000 ; Move back to Y = 18 after purge


G91 ; Relative mode for flicker/wipe


; === Flicker/wipe sequence (Z from -1 to -1.5, 5 cycles, mm/min) ===
G0 Y-25 F18000
G0 Y25 F18000
G0 Z-0.1 F3000
G0 Y-25 F18000
G0 Y25 F18000
G0 Z-0.1 F3000
G0 Y-25 F18000
G0 Y25 F18000
G0 Z-0.1 F3000
G0 Y-25 F18000
G0 Y25 F18000
G0 Z-0.1 F3000
G0 Y-25 F18000
G0 Y25 F18000
G0 Z-0.1 F3000 ; Final Z reaches -1.5


; Switch back to absolute mode and lift Z safely
G90 ; Absolute positioning
G0 Z10 F1500 ; Lift to safe height at moderate speed


; Purge line routine
G92 E0 ; Reset extruder
G1 X-2.0 Y20 Z0.3 F5000.0 ;Move to start position
G1 Z0.2 ;Lower nozzle to printing height
G1 Y145.0 F1500.0 E15 ;Draw the first line
G1 X-1.7 F5000.0 ;Move to side a little
G1 Y30 F1500.0 E15 ;Draw the second line
G92 E0 ; Reset extruder
End G-code (no changes)
G92 E0 ;Reset Extruder
G1 E-1.2 Z{max_layer_z + 0.5} F1800 ;Retract and raise Z
{if max_layer_z < 50}
G1 Z{max_layer_z + 25} F900 ;Raise Z more
{endif}


G1 X2 Y218 F3000 ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed


M84 X Y E ;Disable all steppers but Z

Tagi

nozzleenderwiperke