2000–2013 Chevrolet Impala Front Car Door 6.5" Speaker Bracket
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A front door car speaker bracket for my 2008 Chevrolet Impala LT; created to upgrade to a pair of Scosche HD6504A-WM1SD.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 17
- Wydruki
- 2
- Wyświetlenia
- 132
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Public Domain
In case it isn't clear by the license below or you're unfamiliar with my typical release model, I release this repo into the public domain. You are free to modify, sell, print, remix, etc in both private and commercial settings without attribution. I appreciate a shoutout whenever possible, but if I'm the reason music is playing somewhere, that's enough for me.
Design Philosophy
Uses a max of 45 degree overhangs for widespread printability.
No supports. No post processing. Ready for use off the build plate.
No additional hardware. Uses speaker provided hardware and reuses the car's top screw.
Approximates the same speaker offset used by the OEM speaker + bracket.
PETG to survive being temperature cycled while also being accessible for most printers.
Onshape
Export enabled. I wasn't quite as rigorous with following best practices with this design, so try to let some sins slide.
Alternative Hardware
The screws that come with the scosche speakers are very okay, but having to do several test fitups leads me to believe they aren't hardened. Below is a compatible replacement I used due to a couple heads rounding out.
Speaker Tape
I used closed cell foam tape commonly used for weather stripping in place of name brand speaker tape.
Dimensional Accuracy
This part, like many, requires dimensional accuracy. Dry your filament. Excess moisture tends to make the part run bigger. The largest dimension on this part is 205mm. A good rule of thumb shrink factor is 0.5%, which is ~1mm, and 1mm definitely matters here. For context, that's the difference between being dead on and 40% of the screw hole being out of line.
Fluff
Backstory
The voice coils in my 18 year old car's OEM speakers finally went out, so I challenged myself to make a weekend project out of it. I picked up a pair of Scosche HD65404A-WM1SD speakers and got to work creating a mounting adapter that mirrors the OEM solution. I could have easily opted to direct metal install these speaker and called it a day, but after putting out a printable replacement for my car's notoriously bad actuator gears and having a few positive interactions with others through that, I've kept a mindset that others can benefit from my effort here.

The final model geometry
A note on reverse engineering
If you're someone new to reverse engineering, I highly recommend you check out Zack Freedman's video on using 3d printing to replicate parts. While I don't follow all the advice given there, it's a good place to start and it'll empower how you work. Speaking of which, a lot of that video's insight is in the measurement and fitup testing approach, but all of which can be immediately forgotten about the moment a 3d scanner enters the room. I've yet run one myself, but I've seen how impactful they can be. For now, it's good 'ol Cardboard Aided Design and 0.4mm prints for me. :')
Prototyping
Getting back on track, after a few prints specifically for validating measurements and good fitup on the inner diameter, 4 speaker screw locations, the top screw, and lastly the bottom clip that interfaces with the door panel, I went big and printed the full model. One thing I had forgotten to check was the top screw's washer diameter and because of that, the print wasn't prefect. It ended up being a good thing though, as it gave me an excuse to lower the filament amount for the print and I shaved off 25% off the total amount used. After fixing the washer spacing and the print optimization, I started up both of my printers and let them run into the night. It's always nice waking up to completed print; it's a bit like Christmas as a kid.
Squeaky PETG
Screwing into PETG is near earplug worthy. Putting in 30mm of screw x 8 was rough on my ears. I'm not sure if this is because I picked a 0.5mm overlap for the threads to grab onto or if it's just a side effect of using sheet metal screws on PETG. Either way, consider this your warning.
Wiring, testing, checking phase
I used some female slide connectors, stripped the wires, crimped the connectors on, attached to the speaker, picked a song that I knew had some bass, and gave them a test. I immediately noticed something was off. A speaker being out of phase isn't "slap in your face standout", it's something that you might notice if you're moving around in the car you notice some variation in the music. From past work I knew it was ok to wire them backwards, but in the past my wires were labeled. I did some research on how I might be able to validate the wiring is correct, and while the 9V battery test is a good way to test, I had a pretty easy time just looking at the speaker cones and being able to tell they were sucking in and not pushing outwards. Flipping the connectors fixed the issue and they sound great. Great enough my rear oval speakers definitely have some competition.
Prototype graveyard

Not shown, one "failed" print. The top washer hole was too small. so I opted to fix and reprint. Trying to bore out the hole was hard without a drillpress due to the 45 degree angle.