Bosch Indego S500 rear wheels V3 [commercial use]
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A slim and futuristic, yet sturdy rear wheel for Bosch Indego S500 robotmowers.
- Ocena
- 0 / 5
- Polubienia
- 0
- Wydruki
- 0
- Wyświetlenia
- 124
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor & Garden
- Licencja
- Commercial Use
Note: This is the version for commercial use! See the license details below.
You are allowed to print these wheels for yourself. Take a look at the personal and free version on
History
These are the 3rd iteration Indego wheels I've designed, always learning from previous models.
First generation: stylish wheels but easily loses traction when there is too much dirt/pet droppings in the garden.
Second generation: fixes the issues with dirt, but the grip was not as good in certain situations. Rubber/EPDM helped on the contact surfaces, but it was not ideal.
This is the third generation: it fixes the grip problem for me while keeping a stylish design. All this while consuming less (V1) or about equal (V2) the amount of plastic.
This design features more spread out contactpoints towards the ground. The open legs allow for some flex so it can crawl out some holes instead of digging in and getting stuck. Dirt also keeps getting removed instead of sticking to the wheels and reducing grip.
The wheels are also slightly bigger and deeper for an optimal fitment inside the available space.
Visual comparison V1 vs V3
![]() | ![]() |
V1 (left) and V3 (right) on a similar run. I've tried it multiple times and once the V1 wheel is saturated with dirt, the grip changes dramatically. The V3 wheel just keeps losing its dirt.
Print specifications
Material:
PETG (preferred) to allow some flex and resist UV.
Print settings:
Print it lying on it's back (side that faces the robot)
Layer height: 0.2mm
Perimeters: minimum of 4.
Solid layers (top and bottom): 5
Infill: Gyroid 10%
Use a sticky print plate, glue stick or add a brim to prevent the small feet from detaching until they converge.
Designed for no/minimal supports. I used PrusaSlicer to generate the supports.
Inner upper ring
top of the small feet
center of the wheel where to bolt them to the robot.
Add a solid infill where the bolts need to go for strength purposes (see 3mf)


Assembly
The assembly of the wheel is pretty straight forward. Remove the old wheel and slide this one on. Just mind the alignment of the holes.
Support
I hope this design is useful for others that struggled with the same problem I have.
Like and post makes if it solved the same problem!
Disclaimer
This model works on my own Bosch Indego S500+, but results may vary depending on printer settings, materials, and mower condition. I am not liable for any damage, malfunction, or loss resulting from printing, modifying, using, or selling physical prints of this model. You print, use, modify, and/or sell physical prints at your own risk.
License
This is the commercial-use version of the Indego S500+ wheels. By purchasing this version, you receive a non‑exclusive commercial license that allows you to:
Print and sell physical copies of these wheels
Use the design in your own repair or print‑on‑demand service
Modify the design for your own commercial use (as long as you do not redistribute the digital design files¹
You are NOT allowed to:
Sell, share, or redistribute the digital design files¹
Upload the files to any platform
Offer sublicenses to others
¹ : including but not limited to STL, STEP, 3MF, OBJ or modified versions thereof
For personal use, please download the free CC BY‑NC‑SA version here: 👇

