IKEA NORDEN Table Caster Wheel Holder – Non-Destructive, No Drilling Required

Why?

The IKEA NORDEN table is a beautiful piece of furniture, but at 47kg it's a beast to move.

I use mine almost daily and kept struggling to reposition it; so I designed a simple, non-destructive solution that clips onto the existing table legs without any modification whatsoever.

How it works

The caster wheel is mounted onto the printed bracket using the wheel's standard screw plate. The holder slides onto the bottom of the NORDEN leg (45.4mm wide, 84mm tall foot section) using a snug friction fit and adding only 4–5mm depending on whether you keep the original white plastic feet caps or remove them first.

No drilling, no glue, no permanent modifications >>> fully reversible.

Design Story

When I first looked into adding casters to the NORDEN, the obvious approach was to screw a wheel plate directly into the bottom edge of the leg. But the leg base is only 45.4mm wide, and the wheel mounting plate is 52mm wide; placing screws that close to the edge of a loaded wooden leg felt like a recipe for splitting the wood over time, especially on a table that gets moved almost every day.

The second option was drilling a socket into the bottom face of the leg (there is already one socket 18mm deep and 8.6mm wide). That would have worked mechanically, but it's a one-way modification, once you drill, there's no going back to the original table plus the extra height.

I wanted something fully reversible. So I designed a holder that wraps around the leg and uses the geometry of the foot as the anchor point. The caster bracket extends sideways from the holder, positioning the wheel correctly without touching the wood grain edge at all. The holder itself relies on wall friction and the downward force of the table's weight to stay in place – no fasteners needed on the wooden part.

The result is a mount that installs in seconds, leaves zero marks on the table, and can be removed just as easily if you ever want to restore the original look.

Fit & Assembly Notes

Due to the table's weight (47kg distributed across 4 holders), the fit between the caster plate and the holder bracket is intentionally stiff. You may need some effort to seat the wheel plate fully into the slot.

An additional factor: the mounting plates on these casters are roughly finished on the edges – casting marks and minor burrs are common.

Before assembly, I recommend:

• Running a flat file or fine sandpaper along the edges of the metal plate to remove any burrs

• A light pass with sandpaper on the inner walls of the printed slot if needed

• A rubber mallet or a clamp can help press the plate fully into position

Important: the NORDEN legs are solid wood, and wood naturally expands, contracts, and deforms over time. This means the leg cross-section may not be perfectly consistent across all four feet or may change slightly over the years. If the holder feels loose or wobbly after installation, the fix is simple: apply a few strips of masking tape on the inner walls of the holder before sliding it onto the leg. This takes up the slack and gives a firm, rattle-free fit without any permanent modification.

Once seated correctly, the downward load of the table weight keeps everything firmly in place.

Compatible caster wheels

Designed specifically for 30mm diameter, plate-mount swivel casters, 40kg rated:

OBI Italia art. 4239703 – zinc-plated steel housing, plastic wheel (https://www.obi-italia.it/p/4239703/rotella-laterale-con-rotella-sterzante-30-mm-p-40-kg)

Similar models on Amazon EU (search: "rotella laterale piastra 30mm 40kg") (https://www.amazon.it/8-rotelle-laterali-30-mm/dp/B077S8T7K4/)

4 wheels × 40kg = 160kg total capacity - well above the table's 47kg.

Print settings

• Material: PETG or ASA recommended (load-bearing part under constant stress)

• Perimeters/walls: minimum 10 - critical for layer bonding strength

• Infill: 40%+ recommended

• Layer height: 0.2mm

• Organic supports on build plate only