1 / 8
Ridgid Shop Vac Space-Saving Cyclone Cart Fittings (Thien Baffle System) — zdjęcie 1
1 / 8

Ridgid Shop Vac Space-Saving Cyclone Cart Fittings (Thien Baffle System)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Turn your Ridgid NXT shop vac and a 5-gallon bucket into a compact, single-unit cyclone dust extractor!

Ocena
0 / 5
Polubienia
1
Pobrania
8
Wydruki
0
Wyświetlenia
118
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Standard dust separator carts double the footprint of your vacuum and love to tip over. This project utilizes the vacuum’s existing accessory/extension wand storage slots (just above the wheels) as structural anchors. By printing these custom fittings and using standard, inexpensive PVC pipe, you can mount your DIY Thien Baffle cyclone separator directly above the powerhead, keeping the entire footprint completely stock.

Additional Hardware Needed

  • Pipe: 1 1/4" PVC Pipe (cut to your desired height)

  • Couplers: Standard 2” PVC Couplers (x3 or x4, depending on your leg configuration)

  • Fasteners: Small bolts (0.1875” or approx. M4 / M5) to secure the top fittings to your custom plywood base platform.

  • Fitment Note: If there is slight play between the 2” PVC couplers and your vacuum's accessory stubs, you can print the included Shim file, or simply wrap the inside with 20 Mil Pipe Wrap / Duct Tape for a snug, friction fit.

Component Dimensions & Specifications

Bottom Fitting:                                                                                                                                                                                          This transitions your lower structural support from the vacuum base to the upright legs.

  • Lower Section: OD = 2.373” /  ID = 2” /  Height = 1” (Slips perfectly into a 2” PVC Coupler)

  • Upper Section: OD = 2.05” /  ID = 1.675”  /  Height = 0.8” (Snug friction fit for 1 1/4" PVC pipe)

  • Wall Thickness:  0.1875”

  • Total Height: 1.8”

  • Geometry: Features 45⁰ bevels at both the center transition and the top rim for seamless printing and easier pipe insertion.

Top Fitting:                                                                                                                                                                                                      This mounts directly to the underside of your custom wooden bucket platform.

  • Dimensions: OD = 2.05”  /  ID = 1.675”  /  Height = 1” (Accepts the top of the 1 1/4" PVC leg)

  • Wall Thickness: 0.1875”

  • Mounting: Features a pre-modeled 0.1875” center bolt hole to secure the fitting to your upper plate.

Optional Shim:                                                                                                                                                                                            Used if needed to take up play between the 2" coupler and the vacuum's built-in plastic stubs.

  • Dimensions: OD = 2.373”  /  ID = 2.255”  /  Height = 0.838”

  • Wall Thickness: 0.118”

  • Height: 0.838”

Assembly Instructions

 Prep the Base: Slip a 2" PVC coupler over each of the existing lower accessory stubs on your Ridgid vacuum base. If the fit has play, wrap the stub with a bit of pipe wrap tape or insert the printed shim first.

  1. Insert Bottom Fittings: Press the Bottom Fitting (larger end down) firmly into the top open end of the 2" PVC couplers.

  2. Cut & Install Legs: Cut your 1 1/4" PVC pipe into equal lengths based on how high you want your bucket platform to sit. Insert these pipes into the top of the Bottom Fittings.

  3. Mount Top Platform: Bolt the Top Fittings to the underside corners of your DIY wood platform holding your Thien Baffle bucket.

  4. Final Drop: Line up the Top Fittings with the upright PVC pipes and lower the assembly down into place.

Recommended Print Settings

  • Material: PETG or ABS/ASA is highly recommended for workshop environments for durability and impact resistance, though PLA will work fine if the cart isn't subjected to heavy abuse.

  • Infill: 25 - 40% (Gyroid or Grid for structural compressive strength).

  • Walls/Perimeters: 3-4 lines (Ensures the friction-fit areas are solid plastic rather than infill).

  • Supports: None required.

Explore More Workshop Upgrades

Browse my full catalog of custom adapters, dust collection fittings, and workshop jigs here:

Tagi