AEG Chillflex Pro 12k — Dual-Hose Intake Adapter (AXP34U338CW)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Dual Hose adapter for the AEG Chillflex Pro 12000 (model AXP34U338CW) portable air conditioner.
- Ocena
- 5 / 5
- Polubienia
- 6
- Pobrania
- 72
- Wydruki
- 1
- Wyświetlenia
- 329
- Oceny
- 1
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other House Equipment
- Licencja
- GNU General Public License v3.0
AEG Chillflex Pro 12k — Dual-Hose Intake Adapter
Custom adapter for the AEG Chillflex Pro 12000 (model AXP34U338CW) portable air conditioner. It attaches to the unit's compressor air intake and converts it to a hose connection, allowing the single-hose unit to be run as a dual-hose unit (drawing condenser/compressor intake air from outside rather than from the room).
Version 1


Version 2 (UNTESTED)


Overview
Target unit | AEG Chillflex Pro 12k — AXP34U338CW |
Function | Converts compressor air intake to a hose port (dual-hose conversion) |
Design | Two parts that slot together; bolts clamp the hose attachment closed |
Included files | STEP (editable CAD) + 3MF (print-ready) |
Why dual-hose?
A stock single-hose portable AC exhausts hot air outside but pulls its replacement / compressor intake air from inside the room, creating negative pressure that draws warm, unconditioned air back in through gaps. Feeding the compressor intake from outside via a second hose removes that penalty and improves cooling efficiency.
Version History
Version | Notes |
|---|---|
1 | Initial Release - Used a Dovetail Connector/locator with an overlap to seal off the gap |
2 | Adjusted the locator to make it a central separated tab - NOT CURRENTLY TESTED |
Print Instructions
It fits just fine on a Bambu A1 size printbed (250x250x250 - zero chance on a mini without taking the step file and splitting it yourself.
Orientation with this one is a challenge, as basically all options have positives and negatives. Supports are unavoidable for sure.
I have modified some of the clips and locators design from the original AEG part to better suit 3D printing.
Version 1 - My personal recommendation is orient the bottom part with the middle of the part on the build surface, and the top half with the top of part on the build surface then just auto-tree and send it.
Version 2 - This is designed so that there is a flat surface in the middle that you can orient the print around.
Pretty sure any material would be fine, and any nozzle size would work out ok... I used 0.4 and PLA for my final assembly test and I think I will probably just keep it that way. It's a rough print with wet filament that was not well tuned, but it works.
How it works
The model is made of two parts that slot together and clip in the place of the original filtered air vent on the back of the air con unit.
The bolts clamp the hose attachment together, holding the two halves closed and securing the assembly to the intake.
Heat-set inserts provide the threaded engagement for the bolts in printed plastic. They are inserted on the bottom half
Bill of Materials (hardware)
Hardware is not included with the printed parts — source separately. If you want to change the hardware arrangement, please use the step file to adjust.
Bolts — 2×
Spec | Value |
|---|---|
Type | Hex socket (Allen) cap screw |
Thread | M3 |
Length (minimum) | 14 mm |
Length (recommended) | 16 mm |
Heat-set inserts — 2×
M3 flanged heat-set inserts. Non-flanged would also work, as long as they are ~5mm deep.
Dimension | Value |
|---|---|
Thread | M3 |
Total length | 5.8 mm |
Bottom diameter | 3.75 mm |
Flange diameter | 7.1 mm |
Flange depth | 0.75 mm |
Assembly
Install a heat-set insert into each of the two insert bosses on the bottom part hose port (flange side flush with the surface — heat the insert with a soldering iron and press until the flange seats).
Locators:
For Version 1 - Fit the two halves together, ensuring the dovetails at the sides slot together.
For Version 2 - Fit the central locators and fit the two halves together.
Drive the 2× M3 hex-socket bolts through the relative holes on the top side to clamp the parts
Connect the exhaust/intake hose to the adapter's hose port. This might take a little bit of fiddling, but once its in it holds very tight.
Clip into the air intake side of the air con.
Optional
You could use some glue, epoxy, or construction sealant to seal up the split, but I don't think it's really needed.
STEP files
If anyone has a similar model aircon with some small differences, or if anyone wants to improve my version, please feel free to use the step files to modify as needed. If you share, please abide by the license selected.
