QIDI Plus 4 QIDI Box Filament Inlet Adapter (PC4-M6)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Prevents the QIDI Box PTFE tube from slipping out while adding a secure PC4-M6 filament inlet.
- Ocena
- 0 / 5
- Polubienia
- 3
- Pobrania
- 17
- Wydruki
- 0
- Wyświetlenia
- 118
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Other Printer Parts & Upgrades
- Licencja
- GNU General Public License v3.0
English below
QIDI Plus 4 PC4-M6 Filamentführungs-Flansch für den Betrieb mit der QIDI Box
Dieser Flansch unterstützt die originale Filamentdurchführung des QIDI Plus 4 und ergänzt sie um eine PC4-M6-Pneumatikkupplung. Dadurch wird der PTFE-Schlauch der QIDI Box sicher fixiert und kann nicht mehr aus dem Druckergehäuse herausrutschen.
Beim QIDI Plus 4 wird der PTFE-Schlauch der QIDI Box lediglich durch eine Gummitülle geführt und nicht mechanisch gesichert. Durch die Bewegungen des Druckkopfs sowie den Filamentvorschub kann sich der Schlauch mit der Zeit aus dem Gehäuse ziehen. Der Flansch verhindert dies zuverlässig und sorgt gleichzeitig für eine saubere und stabile Filamentführung.
Benötigte Teile
1 × PC4-M6 Pneumatik-Schnellverbinder
1 × PTFE-Schlauch, 30 mm lang
Doppelseitiges Klebeband, ca. 50 × 25 mm (zwei schmale Streifen)
1 × Skalpell oder scharfes Bastelmesser zum leichten Aufweiten des PTFE-Schlauchs
Montage
Weite eine Seite des 30 mm langen PTFE-Schlauchs innen leicht mit einem Skalpell oder scharfen Bastelmesser auf. Dadurch wird das Einführen des Filaments deutlich erleichtert.
Stecke den PTFE-Schlauch mit der aufgeweiteten Seite in die flache Seite des Flansches.
Schraube den PC4-M6-Schnellverbinder in die erhöhte Seite des Flansches.
Prüfe vor dem Verkleben unbedingt, ob sich das Filament ohne spürbaren Widerstand durch den kompletten Aufbau schieben lässt.
Bringe zwei schmale Streifen doppelseitiges Klebeband auf der Rückseite des Flansches an und klebe ihn über die vorhandene Filamentdurchführung des Druckers.
Druckempfehlung
Ich habe den Flansch aus ABS-GF25 gedruckt. Das Material ist temperaturbeständig und ausreichend steif für diese Anwendung.
Ich hoffe, dieser kleine Helfer erleichtert auch anderen Besitzern eines QIDI Plus 4 den Betrieb mit der QIDI Box. Viel Spaß beim Drucken!
English
QIDI Plus 4 PC4-M6 Filament Guide Flange for Use with the QIDI Box
This flange supports the original filament entry of the QIDI Plus 4 by adding a PC4-M6 pneumatic push-fit connector. It securely holds the PTFE tube coming from the QIDI Box and prevents it from being pulled out of the printer housing.
On the QIDI Plus 4, the PTFE tube from the QIDI Box is only guided through a rubber grommet and is not mechanically secured. During printing, movement of the print head and the force applied by the QIDI Box can gradually pull the PTFE tube out of the housing. This flange reliably prevents that while providing a clean and stable filament path.
Required Parts
1 × PC4-M6 pneumatic push-fit connector
1 × 30 mm PTFE tube
Double-sided adhesive tape, approximately 50 × 25 mm (two narrow strips)
1 × Scalpel or sharp hobby knife for slightly flaring the inside of the PTFE tube
Assembly
Slightly flare one end of the 30 mm PTFE tube from the inside using a scalpel or a sharp hobby knife. This helps the filament enter the tube smoothly.
Insert the PTFE tube into the flat side of the flange with the flared end facing inward.
Screw the PC4-M6 pneumatic fitting into the raised side of the flange.
Before attaching the flange, make sure the filament slides through the complete assembly without noticeable resistance.
Apply two narrow strips of double-sided tape to the back of the flange and attach it over the printer’s original filament entry.
Print Recommendation
I printed the flange in ABS-GF25, which provides excellent stiffness and sufficient heat resistance for this application.
I hope this small accessory makes using the QIDI Box more enjoyable for other QIDI Plus 4 owners. Happy printing!