1 / 5
Flat-Lay Product Photo Rig (overhead phone mount + paper sweep backdrop) — zdjęcie 1
1 / 5

Flat-Lay Product Photo Rig (overhead phone mount + paper sweep backdrop)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Desk-clamp overhead phone mount plus a paper sweep backdrop. No screws, no supports, one rubber band.

Ocena
0 / 5
Polubienia
1
Pobrania
22
Wydruki
0
Wyświetlenia
201
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Photo & Video
Licencja
Creative Commons — Attribution

WHAT IT IS

An overhead phone rig for flat-lay and top-down product shots, and a matching paper sweep backdrop that gives you a seamless, shadow-free background on a normal desk.

I built it because I run a Shopify marketing agency and the least glamorous fix for a bad product page is almost always the same one: shoot every SKU from the same height on the same clean background. Paying a studio for that stops making sense past a few hundred products.

It clamps to the edge of a desk or table (12–26 mm tops), so nothing sits in your shot and you get the same framing every single time. That repeatability is the whole point: if every product photo is shot from the same height at the same angle on the same background, your listings look like a set instead of a scrapbook.

SIZED FOR REAL PRODUCTS

The post is stackable — each segment is 180 mm of usable height with a tenon on top, so print two for about 360 mm of post, or three if you shoot something tall. The arm slides anywhere on it and locks with a wedge.

The sweep backdrop is deep and tall to match: a 70 mm flat run before the curve starts, then a 75 mm radius rising to about 155 mm. Comfortably clears bottles, boxes, shoes and mid-size homewares rather than just jewellery and cards.

ZERO HARDWARE

No M3s, no heat-set inserts, no nuts. The whole rig is held together by two printed wedges:

- The clamp wedge drives in under the desk top and self-locks (1:7.4 taper).

- The collar wedge drops into the arm collar and locks the arm at any height on the post.

Both knock out with a tap when you want to move or pack the rig away.

The only non-printed part is one rubber band (a #64 office band or a hair tie), which pulls the two cradle jaws onto your phone.

PARTS LIST

1. Clamp body — 1x — 96 × 60 × 97 mm

2. Clamp wedge — 1x — 112 × 54 × 27 mm

3. Post segment — 2 or more — 204 × 20 × 20 mm

4. Arm + collar + rail — 1x — 210 × 132 × 42 mm

5. Collar wedge — 1x — 14 × 58 × 18 mm

6. Cradle jaw — 2x — 61 × 41 × 44 mm

7. Backdrop bracket — 2x — 158 × 162 × 30 mm

Every part fits a 220 × 220 bed without rotating.

FITS

- Phones roughly 62–90 mm wide, up to 13 mm thick including a case.

- Desk and table tops 12–26 mm thick (thicker tops up to 32 mm work without the wedge, just less grip).

- Products up to about 150 mm tall under the sweep, taller if you add a third post segment and stand the brackets further apart.

- Backdrop brackets take a sheet up to about 1.6 mm thick — A3 card, a cut-down poster board, or a sheet of white PP. Feed A3 in with the 420 mm edge across the two brackets.

PRINT SETTINGS

- Supports: none. Every part has a flat face on the bed and no overhang steeper than 45°, other than one 20 mm bridge across the post socket.

- Layer height: 0.2 mm

- Walls: 4 perimeters

- Infill: 30% for the clamp body, post segments and arm; 25% is fine elsewhere

- Material: PLA is fine indoors. PETG or ASA if the rig lives near a window.

- Orientation: all STLs are already saved in the orientation they should be printed in — drop them on the plate as-is.

The full set is about 700 cm3 of part volume — call it 350–400 g of filament and somewhere around 22–24 hours on a 0.4 mm nozzle at 0.2 mm.

ASSEMBLY

1. Hook the clamp body over the edge of your desk, back plate flat against the edge.

2. Slide the clamp wedge in under the desk top, thin end first, between the bottom jaw rails. Push it firmly by hand, then give the tail a tap. It should not move when you push the clamp sideways.

3. Drop the first post segment into the socket, tenon pointing up.

4. Press the second segment down onto that tenon. Add a third if you need the height.

5. Slide the arm collar onto the post at the height you want, then drop the collar wedge into the gap on the back of the collar and press it home. Tap it out to change height. Give yourself roughly twice the height of your product.

6. Thread a cradle jaw onto each end of the rail. Loop the rubber band over the two horns.

7. Slide your phone into the jaw channels, camera end pointing out past the rail so nothing blocks the lens. Slide the jaws along the rail to set the width.

8. Stand the two backdrop brackets about 250 mm apart on the desk and slide a sheet of A3 card down into the slots. It forms the curve on its own.

Once the arm is above about 300 mm, put something heavy on the desk over the clamp's top jaw, or run the clamp on the short edge of the desk. Long lever, small clamp.

GETTING GOOD PHOTOS OUT OF IT

- Put the sweep so the flat part of the curve sits directly under the phone. Any shadow behind the product falls onto the curve instead of a hard corner.

- One window to the side and a sheet of white card on the opposite side as a bounce will beat a ring light nine times out of ten.

- Shoot with the phone's 1x lens, not the ultra-wide — the ultra-wide bends straight edges and makes packaging look wrong.

- Lock exposure and white balance before you start so a batch of products matches

Tagi