1 / 1
Torreva AD5X enclosure - Pass-through plate for IFS tubes mod — zdjęcie 1

Torreva AD5X enclosure - Pass-through plate for IFS tubes mod

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

If you don't like the bulky IFS tube cover, here's an alternative option.

Ocena
0 / 5
Polubienia
2
Pobrania
5
Wydruki
0
Wyświetlenia
188
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Open Community License v1.1 + General Attribution v1

I don't charge for my functional models. Please consider purchasing some of my paid models as a way to support both my work, and this great website: https://www.printables.com/@ninjamida/store

Check out my other AD5X replacement parts, mods and upgrades (all free!).


If you're not a fan of the IFS tube cover from the Torreva enclosure, here's an alternative option - a cover plate with four slots for the tubes to pass through, and an (optional) TPU piece with flaps to better seal the gaps.

This completely replaces the "IFS-Cover" part. If you are in the process of building a new Torreva enclosure and you intend to use this mod, you should skip printing the IFS-Cover piece and instead attach this in its place. Otherwise, remove that part from your enclosure and replace it with this.

You must disconnect the tubes at the IFS side in order to install (or remove) this mod. For this reason, I highly recommend using it in conjuction with an ECAS04 or PC4-M10 mod for your IFS tube connectors.

Non-printed parts
- 4x M3 hex nut
- 4x M3x8 (without TPU plate) or M3x10 (with TPU plate) screws; cap head recommended
- For attaching it to the Torreva enclosure, you will reuse the screws that were previously used to attach IFS-Cover

Print instructions
- 0.6mm nozzle recommended but not required
- MainPlate should be printed in PETG (other rigid filaments, except for PLA, are likely fine too). Supports are recommended for the counterbore in the screw holes but are not needed anywhere else. Print with the large flat side facing down.
- TPUPlate (optional part) should be printed in TPU 95A (other grades untested, feel free to try) or a material with similar flexibility and similar or better heat-resistance; 1 wall loop, 2 bottom layers, 3 top layers, 0.2mm (or thinner) layer height. This is for a 0.6mm nozzle; you may need two wall loops on a 0.4. No supports required.
- LockPlate (only used if also using TPUPlate) should be printed with the same settings and materials as MainPlate, and requires supports in the hex nut counterbore.

Assembly instructions
- If you are not using TPUPlate and LockPlate, then skip to Installation Instructions (as you will just be using MainPlate as a single piece).
- Double check that the thin slits in TPUPlate are able to fold apart freely and have not fused together. If they have, use a thin blade to slit them open. (The gap should be enough that this will never happen, but I have noted this just in case.)
- Insert hex nuts into the four recesses on LockPlate.
- Snap TPUPlate onto LockPlate. It doesn't matter which way faces up.
- Insert LockPlate into the gap on the rear side of MainPlate, with the hex nuts facing outwards and TPUPlate facing inwards.
- Use the four screws to attach LockPlate. Tighten them until the respective corner of LockPlate starts to flex inwards, then loosen them until it almost sits flat again.

Installation instructions
- Disconnect your IFS tubes from the IFS, and remove IFS-Cover from your Torreva enclosure (if installed)
- Install this assembled part in place of IFS-Cover, using the same screws that were used to hold IFS-Cover in place.
- Push the IFS tubes through the four slots and reconnect them to the IFS.

Tagi