Pool Water Level Gauge – Clip-On, 10 Sizes (5–14 cm)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Clip-on pool water level gauge in 10 sizes, matched to your skimmer for instant HIGH, IDEAL, and LOW readings.
- Ocena
- 0 / 5
- Polubienia
- 6
- Pobrania
- 12
- Wydruki
- 0
- Wyświetlenia
- 131
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor & Garden
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
Stop guessing when your pool needs water
Is the water too high? Is it at the correct level? Does the pool need to be topped up?
This simple clip-on gauge makes the answer visible at a glance:
HIGH: the water is above the target range
IDEAL: the water is at the ideal level
LOW: it is time to add water
Instead of bending down to compare the waterline with the skimmer every time, just look at the marker.
Designed for your pool
The correct distance between the pool ledge and waterline is different from pool to pool, so a single fixed-size gauge would not work for everyone.
This download includes 10 solid sizes from 5 cm through 14 cm, allowing you to choose the version that matches your pool.
The usual target waterline is approximately halfway up the skimmer opening, which helps the skimmer operate without drawing air or becoming fully submerged. Always follow your pool manufacturer’s instructions when they differ.
Choosing the correct size
Locate the skimmer opening inside your pool.
Find the vertical center of the opening.
Measure vertically from the underside of the pool ledge to the center of the skimmer opening.
Choose the gauge with the closest matching measurement.
Clip it onto the ledge with the labels facing the pool.
For example, if your measurement is approximately 8 cm, print the 8 cm model.
The IDEAL line should align with the center of the skimmer opening. The HIGH and LOW lines provide an easy visual warning when the level moves outside the preferred area.
Why ten separate sizes?
Each version is a solid, purpose-sized model rather than an adjustable assembly.
That means:
No screws
No sliding parts
No calibration after installation
No separate hardware
Nothing to loosen or lose beside the pool
A clean and durable one-piece print
Measure once, print the correct size, and clip it into place.
Print settings
For the best result, print with the labeled side facing down on the build plate.
Recommended settings:
Supports: None
Infill: 50% rectilinear
Orientation: Labeled side down
Layer height: 0.20 mm suggested
Perimeters: 3 or more suggested
Nozzle: Standard 0.40 mm nozzle
Material: PETG recommended
ASA is also a strong option for long-term outdoor exposure because of its ultraviolet and temperature resistance, although it requires more controlled printing conditions and ventilation.
Avoid leaving a PLA version permanently outdoors in direct summer sunlight, since PLA has lower heat and ultraviolet resistance.
Standard and looser versions
The standard marker is designed to grip the pool ledge securely.
Fit can vary depending on:
Pool ledge thickness
Material choice
Printer calibration
Extrusion width
Number of walls
When the standard version feels too stiff or is difficult to install, print:
Marker-LOOSER.stl
The looser version provides additional flexibility and is easier to clip onto thicker or less forgiving ledges.
Do not force the marker onto the pool. Use the looser version when necessary.
Installation
Confirm that the selected size matches your measurement.
Inspect the print for rough or sharp edges.
Gently rest the gauge over the pool ledge.
Position it where it can be seen easily but will not interfere with the skimmer, cover, ladder, or swimmers.
Check that the IDEAL line corresponds with the center of the skimmer opening.
No tools or permanent modifications are required.
Included files
5 cm water-level gauge
6 cm water-level gauge
7 cm water-level gauge
8 cm water-level gauge
9 cm water-level gauge
10 cm water-level gauge
11 cm water-level gauge
12 cm water-level gauge
13 cm water-level gauge
14 cm water-level gauge
Marker
Marker-LOOSE
Safety and care
This gauge is a visual reference tool, not an electronic sensor or automatic filling system.
Follow the water-level recommendations supplied by your pool manufacturer.
Inspect the gauge periodically for cracking, warping, or sharp edges.
Remove or replace damaged prints.
Do not install it where swimmers could step on, grab, or collide with it.
Do not allow it to obstruct the skimmer, pool cover, ladder, or filtration equipment.
Rinse it with clean water when chemical residue accumulates.
Material behavior may vary depending on sunlight, temperature, pool chemicals, and filament manufacturer.
Share your setup
Pool ledges and skimmers come in many shapes and sizes. Post a make showing which size fits your pool and mention the material you used; it may help another pool owner choose the correct version.