1 / 3
Monitor Riser Legs - Screwed to a Board, 65/115/165 mm, Fits a 170 mm Bed — zdjęcie 1
1 / 3

Monitor Riser Legs - Screwed to a Board, 65/115/165 mm, Fits a 170 mm Bed

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Four printed legs screwed to a 1x10 board. No printed part is ever in bending, so it cannot creep.

Ocena
0 / 5
Polubienia
1
Pobrania
0
Wydruki
0
Wyświetlenia
32
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Office
Licencja
Creative Commons — Attribution

**Version 2 - please use the riser-v2-* files. The earlier files are left attached only so nobody loses a part mid-print; they are superseded.**

Four printed legs screwed to a plank. A monitor riser sized for a printer that cannot print a monitor riser - no part exceeds 170 mm in any direction.

Five files. One spacer, one cap, and a foot in three sizes.

- 65 mm lift - 4 feet + 4 spacers + 4 caps, 689 g

- 115 mm lift - 4 feet + 12 spacers + 4 caps, 797 g

- 165 mm lift - 4 feet + 20 spacers + 4 caps, 906 g

The spacer and the cap are the same file at every height. Only the foot changes, because a taller stack needs a wider base.

You also need: a 1x10 board (1x12 for the 165 mm version), 4 lengths of M5 threaded rod with 8 M5 nuts, and 8 wood screws, 4 x 30 mm.

## How the board is fixed down

Two wood screws per leg, straight down through the board into the cap.

The cap is a flat pad with two 2.9 mm pilot holes 34 mm apart. Drill nothing in the plastic - the pilots are already there, cut for the screw's core so the thread bites. Countersink the board so the heads sit flush, put the leg where you want it, and drive the screws.

That is the whole fixing. The board cannot lift, slide or twist, and there is nothing to snap.

## Will my monitor fit?

The riser does not grip the monitor - nothing in this category can, because monitor feet have no standard at all. What matters is that the platform is bigger than the foot standing on it, in both directions.

Depth: a 1x10 is 235 mm deep. The deepest monitor foot with a published figure is the 27 inch Dell P2722H at 190.1 mm. A 1x8 - 184 mm - is NOT enough, and version 1 of this model wrongly specified one.

Width: cut the board to whatever you like. Put the legs 40-60 mm in from each end so the overhang is short, and make sure the board is wider than the monitor's foot.

The board is a flat continuous surface, so any foot shape sits on it - round, tripod, T-bar or plate. If your monitor came with a clamp or a VESA arm instead of a foot, this is not the product you want.

## Why the span is a plank and not a print

Because PLA creeps, and a monitor is a permanent load.

The one published study I could find on creep in FDM polymers tested six materials at 10 and 20 MPa and named PLA outright as the material with the worst creep resistance - and noted PLA, TPLA and ABS ruptured at 60 C, which is a desk beside a sunny window in July.

Every fully printed riser puts PLA in sustained bending across a 400 mm span under 5 to 7 kg of monitor, for years. So there is no printed part in this design that is ever in bending. The legs are columns in pure compression and the board carries every bending moment. At the rated 20 kg with a 2x allowance for somebody leaning on it, the stress in the column is 0.26 MPa.

Nominal lumber is also the one hard published dimension in this whole category: NIST PS 20 makes 1x6, 1x8, 1x10 and 1x12 all exactly 19 mm thick, everywhere, guaranteed.

## Height is yours, not mine

OSHA and ANSI/HFES 100-2007 both say only that the screen centre wants to sit 15 to 25 degrees below your eye level. Worked against published seated eye heights on a normal desk, the riser a person needs is anywhere from nothing to about 150 mm, and it differs for everyone.

So the leg is a stack: a foot, as many 25 mm spacers as you want, and a cap. Print two more spacers per leg and it is 50 mm taller. Nothing else changes.

## Assembly

1. Drop an M5 nut into the pocket in the foot.

2. Stack the spacers. Each seats on a flat shoulder and the spigot keys it against twisting.

3. Put the cap on, drop an M5 nut into the seat in the top, and run M5 threaded rod (68 / 118 / 168 mm) up the middle. Nip it up.

4. Stand the four legs on the desk, lay the board on them, and drive two wood screws down through the board into each cap.

## Printing

- No supports anywhere. Every module is a vertical prism bored right through; the pilot holes and the nut seats open upward. The only horizontal face is the bearing shoulder.

- 0.20 mm layers, 15% infill, PLA.

- Print in the orientation the files come in.

## One honest limit

This does not save filament over a fully printed riser - it is about the same or a little more. The cap cannot be hollowed without support, and I would rather ship a dense cap than a support raft. What you get for it is a riser that will not sag.

Tagi