1 / 14
Weather Dial Fridge Magnet — spin it to today's weather — zdjęcie 1
1 / 14

Weather Dial Fridge Magnet — spin it to today's weather

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A fridge magnet with a live front. Thumb the knurled rim through the side notch and the dial clicks into four detented…

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
14
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

Weather Dial Fridge Magnet — spin it to today's weather

A fridge magnet with a live front. Thumb the knurled rim through the notch in the side and the dial clicks into four detented positions — sun, rain, cloud, snow — showing exactly one icon at a time through the porthole.

It holds its position by itself. No sliding tab that drifts, no loose token to lose behind the fridge, no magnet-and-paperclip arrangement that falls apart the first time somebody slams the door.

Ø62 × 17 mm. Three printed parts. No glue, no screws, no supports.

The magnets are sealed inside

This is the part worth reading before you slice.

Most printed magnets have an open pocket in the back, with the magnet glued in and its bare face against the door. Neodymium rusts, it scratches paint, and sooner or later the glue lets go.

Here the three pockets are fully closed cavities — 0.4 mm of plastic below them on the fridge side, 0.6 mm above on the dial side. Neither face of the finished back plate has a hole in it anywhere.

There is no assembly order that gets a rigid magnet into a sealed cavity, so the discs go in during the print, at a single pause at Z = 3.6 mm. The printer stops with a plain 3.6 mm disc in front of you and three open holes in it; you drop a magnet into each and hit resume. The next layer bridges the Ø5.3 mm opening and closes them in for good.

That is the whole assembly for the magnets: about ten seconds, once, with no glue anywhere near it.

Three small discs on a bolt circle, not one big central one. A single central magnet gives no resistance to twist, so thumbing the dial would just spin the whole puck on the door. Three out at r20 have the leverage to hold it still.

Hardware: 3 × Ø5 × 3 mm neodymium discs. Polarity does not matter.

The dial prints in five colours — with nothing to group by hand

The dial ships as five STL files that share one coordinate system: the body, plus one file per icon.

Select all five, import them together, and answer Yes to "load as a single object with multiple parts?". You get five named parts in the list — dial_body, icon_sun, icon_cloud, icon_rain, icon_snow — and you assign a filament to each by name. Nothing to split, nothing to hunt for, nothing to line up.

It ships this way for a concrete reason. As a single icons file, Split to Parts would hand you 15 pieces, not 4 — it divides by connected component, and the sun's eight rays stand clear of its disc while the rain's three drops stand clear of its cloud. Separate files skip that entirely.

Single-colour is fine too: print the body and the four icons in one filament and the icons still read, because they stand 1.2 mm proud of the face.

Parts

  • weather_dial_magnet_back.stl ×1 — housing: 3 sealed magnet cavities, centre axle, bearing hub, the flexing detent leaf, outer wall and retention bead

  • weather_dial_magnet_dial_body.stl ×1 — the spinning dial: knurled rim, centre bore, detent groove underneath

  • weather_dial_magnet_icon_sun.stl ×1 — sun icon, its own part and its own colour

  • weather_dial_magnet_icon_cloud.stl ×1 — cloud icon

  • weather_dial_magnet_icon_rain.stl ×1 — rain icon

  • weather_dial_magnet_icon_snow.stl ×1 — snow icon

  • weather_dial_magnet_face.stl ×1 — snap-on cover: porthole window and thumb notch

  • weather_dial_magnet_coupon_base.stl + coupon_dial.stl — optional 15-minute fit test

Three physical parts, once the dial's five files are printed as one object.

Printing guide

Try the coupon first. coupon_base plus coupon_dial is a cut-down pair that tests the two things that can actually be wrong on your printer — the bore fit on the axle and the detent click — in about 15 minutes. If the coupon clicks, the real thing will.

Material. PLA is fine for the dial and the face; they are rigid parts that just sit there. For the back plate, PETG is the better choice: its detent leaf bends every single time you click the dial, and PLA fatigues under repeated flexing. PLA works, it simply won't last as many years of clicking.

Settings. 0.2 mm layers, 3 walls, 15 % infill. No supports anywhere, and no brim. Every part lands a large flat face on the bed.

Orientation — all the STLs export ready to slice. Do not rotate them. The face plate in particular is already flipped in the export: its snap skirt hangs below the plate in the assembled model, so if you slice it in assembly orientation the Ø62 disc has to bridge 2.7 mm of air resting on a thin ring, and it fails.

The pause, in Bambu Studio. Slice the back plate, open Preview, drag the layer slider to the first layer you want printed after the pause, then right-click the slider handle and choose Add Pause. At 0.2 mm layers, Z = 3.6 mm is after the 18th layer, immediately before the first roof layer.

At the pause: drop one magnet into each cavity and check that none stands proud before you resume — a disc sticking up gets clipped by the nozzle on the next pass. Each cavity is deliberately 0.2 mm deeper than the magnet is thick, because stock discs run over nominal. That headroom is not slack to tune out.

If you print at a layer height other than 0.2 mm, recompute the pause — it is magnet_skin + magnet_h + magnet_z_clr in the source, and every term is a whole number of layers at 0.2 so that it lands exactly on a boundary.

Never use Split to Parts on the back plate. It splits by connected component, and the three magnet cavities are sealed voids — they come back as solid positive parts and silently fill the pockets in. The back plate is a single-colour part and needs no splitting anyway.

Assembly — about a minute

  1. Check the detent leaf on the finished back plate. The narrow slot near the middle is a moat cutting clean through the floor, leaving a long thin tongue anchored at one end. Push it sideways with a fingernail: it must visibly spring back. If it feels solid, the slot fused and the dial will not turn.

  2. Drop the dial onto the axle, icons facing up. It rests on the bearing hub — no force needed, the bore is a 0.35 mm slip fit.

  3. Spin it now, before the cover goes on. You should feel four distinct clicks per revolution as the leaf's tower rides over the four lobes in the dial's underside groove.

  4. Snap the face plate on. Line the thumb notch up with the gap in the housing wall — both sit at the bottom, directly opposite the porthole at the top. Thumb below, read above. Press straight down until the barb springs past the bead inside the wall. It comes apart again if you pull firmly and evenly.

Source

Designed from scratch in parametric OpenSCAD — no AI-generated geometry, no bundled third-party libraries. The .scad is attached and everything is a named parameter at the top: magnet size and count (magnet_d, magnet_h, magnet_n, magnet_bc, with the pause height deriving itself), detent feel (det_lobe_or, tongue_w, tongue_root), snap strength (barb_or versus bead_ir), and the icons themselves. Swap the four weather icons for moods, chores, laundry symbols or whose turn it is to cook — the dial mechanism does not care what is drawn on it.

Tagi