1 / 1
Quena — 3D Printed Andean Notch Flute in G — zdjęcie 1

Quena — 3D Printed Andean Notch Flute in G

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A 3D-printed quena (end-blown Andean notch flute) in G -- the traditional home key for this instrument.

Ocena
0 / 5
Polubienia
0
Pobrania
14
Wydruki
0
Wyświetlenia
60
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Music
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

# G Quena -- 3D Printed, 20mm Bore

A 3D-printed quena (end-blown Andean notch flute) in G -- the

traditional home key for this instrument, so nothing exotic about the

pitch choice. Built as a direct notch-embouchure adaptation of an

existing, already-tuned 20mm-bore Alto G whistle, rather than designed

from scratch: https://www.printables.com/model/1791116-g-alto-tinwhistle-20mm-bore-printed-fipple-mouthpi

## Three pieces

- Head -- the notch (embouchure) end. Rounded U-shaped notch, not a

sharp V, for a more forgiving blowing angle while learning the

instrument and a closer match to the worn rim shape on traditional

cane quenas.

- Middle -- 6 front finger holes plus 1 back thumb hole (7 total,

the traditional layout).

- Foot -- unmodified from the source whistle's own foot piece. No

changes needed; the bore and joint already matched.

## Playing status

Confirmed against a tuner: **the full first octave is correctly in

tune.** That's the core validation for the whole design -- the hole

positions were carried over from an already-tuned fipple whistle by

translating them into distances from the acoustic origin rather than

guessed at fresh, and the tuner check confirms that transfer actually

worked.

The second octave (reached by overblowing, standard for a quena --

there's no register key) gets unstable partway through in testing so

far. Given the first octave is confirmed correct on the same air

column, this points at embouchure control rather than a bore or hole

problem -- the overblown register on any notch flute takes real

practice to control consistently, more so than on a ducted/fipple

instrument, and this is a first attempt on a genuinely difficult

embouchure type. Not treating this as a design defect unless further

playing suggests otherwise.

One thing worth noting for anyone else building this: the thumb hole

turned out to help reach the higher octave cleanly, acting something

like a register vent rather than only extending the low end of the

scale, which wasn't specifically designed for -- a nice bit of

behavior that emerged from testing rather than being planned.

## Known limitations, honestly

- The notch's acoustic end-correction was estimated by analogy to the

source whistle's fipple, not measured directly -- close enough that

the first octave came out correctly tuned, but not a guaranteed

match for a different bore or key.

- Hole diameters were carried over directly from the fipple whistle as

a first-pass estimate. They may still want individual adjustment

(enlarging, never shrinking) as more playing reveals any notes

sitting slightly off from the rest.

- This is one player's results on one build. Limitations noted above

are about the instrument's design process; the second-octave

instability specifically looks like a player-experience issue, not

a design one.

License

CC BY-NC-SA — free to use, remix, and share for non-commercial purposes with attribution.

Credits

Design by Untemperedsteel. OpenSCAD development assisted by Claude (Anthropic).

Tagi