Solder Fume Extractor — 120mm PC Fan (DIY, fully analog)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
DIY solder fume extractor with a 120mm PC fan. Fully analog: latching on/off + PWM speed control. No microcontroller.
- Ocena
- 0 / 5
- Polubienia
- 104
- Pobrania
- 106
- Wydruki
- 0
- Wyświetlenia
- 1685
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Tools
- Licencja
- Creative Commons — Attribution — Noncommercial
A compact, 3D-printable solder fume extractor built around a standard 120mm PC fan. Instead of buying one off the shelf, this is a complete DIY build: the fan pulls flux fumes away from your face, driven by a fully analog control board that gives you a real latching on/off button and smooth PWM speed control — no microcontroller, just 555 timers and transistors.

These files are the printed housing/enclosure. The fan, electronics, and fasteners are sourced separately — a full parts list (BOM) is included, and the entire build is documented step by step, mistakes and all, on the Deu Tela channel.
Watch the full build! 🎬
I recorded the entire process of making this project and split it into 3 videos:
1. Designing the project & testing on the breadboard
2. Soldering the components onto the perfboard
3. Building a case & finishing the project
You'll also need: a 120mm 4-pin PWM fan, a 12V power supply, the control-board components (see the included parts list), plus 4× M3 heat-set inserts and 4× M3 screws.
SOLDER FUME EXTRACTOR — PARTS LIST
00 · Structure & Assembly
1× Fan 120mm 4-pin PWM — 4-wire PC cooler (I used the Thermalright TL-C12C, 12V / 0.2A)
1× 12V DC power supply — Wall adapter, 12V ≥0.5A (I used a 12V / 1.5A APD)
1× Perfboard — Prototyping board (isolated pads) for the final soldering
4× Heat-set insert M3x4x5 — M3 thread, anchors the enclosure
4× Screw M3x4x5 — Fastens the enclosure into the inserts
01 · Latch — the on/off
1× NE555 — The 555 timer acting as a 1-bit memory (the latch)
3× Resistor 100k — 2× divider on pins 2/6 (~6V) + 1× output → trigger cap
1× Capacitor 10µF — Holds the state (the latch's memory)
1× Resistor 1k — Limits the indicator LED current
1× Green LED 3mm — Shows that the extractor is on
1× Push button — Momentary on/off button
02 · Power cut — "press and it dies"
1× PNP transistor S8550 — The power switch: turns the fan's +12V on/off
1× NPN transistor PN2222 — Translates the latch signal to drive the PNP
1× Resistor 1k — Limits the PN2222 base current
1× Resistor 10k — Pull-up: keeps the fan OFF by default
1× Resistor 1k — S8550 base → PN2222 collector (without it, it overheats!)
1× Diode 1N4007 — Flyback protection against the fan coil's spike
03 · PWM — the speed control
1× NE555 — Second 555, generating the PWM signal
1× Resistor 1k — Charge path: +12V → pin 7 (dis)
1× Capacitor 10nF (103) — Timing cap (Ct), sets the frequency (~kHz)
1× Potentiometer B10K — The knob that sets the speed
2× Diode 1N4148 — Split the Ct charge/discharge (vary duty, fixed freq)
1× Capacitor 100nF (104) — Pin 5 (ctl) noise filter
1× Resistor 1k — Limits the output transistor's base current
1× NPN transistor PN2222 — Open-collector on the fan's PWM (blue) wire
04 · Wiring
Silicone wire 22 AWG — Flexible, for what leaves the board (fan, supply, button, pot)
Component leads — Trimmed offcuts, short jumps on the board
Shopping summary (group by value)
Semiconductors: 2× NE555 · 4× PN2222 (NPN) · 1× S8550 (PNP) · 1× green LED · 2× 1N4148 · 1× 1N4007
Resistors: 5× 1k · 1× 10k · 3× 100k
Capacitors: 1× 10µF · 1× 100nF (104) · 1× 10nF (103)
Others: 1× B10K potentiometer · 1× push button
Substitutions: any 120mm 4-pin (PWM) PC fan works, as does any 12V ≥0.5A supply. The PNP can be a 2N2907/BC327 instead of the S8550. Always check each transistor's pinout in its datasheet before soldering — the S8550 and PN2222 don't share the same pin order.
Designed and documented by Deu Tela — deutela.com.br