1 / 3
Unofficial Orion Lynx 2.1 → GFZ BCAR Adapter — zdjęcie 1
1 / 3

Unofficial Orion Lynx 2.1 → GFZ BCAR Adapter

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Custom adapter to fit a GFZ Bcar onto a 45cm barrel for the stock Lynx 2.1 shroud.

Ocena
0 / 5
Polubienia
0
Pobrania
0
Wydruki
0
Wyświetlenia
44
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

A compact, pinned adapter designed to mount a GFZ 3×5 BCAR to the Orion Lynx 2.1 while retaining the Lynx's stock front shroud pin.

This adapter was developed through several physical test-fit revisions on an actual Lynx 2.1 build. The final V4.3 version provides a snug barrel fit, secure pin retention, and allows the GFZ 3×5 BCAR to sit significantly closer to the front of the blaster than earlier versions.

Compatibility

Designed and physically tested with:

  • Orion Lynx 2.1

  • GFZ 3×5 BCAR

  • 15.93 mm OD barrel

  • Stock Lynx 2.1 front shroud retention pin

The barrel interface on this version is 16.05 mm ID, so fit may vary with barrels that have a different outside diameter.

Final V4.3 Dimensions

  • Barrel bore: 16.05 mm

  • Tested barrel OD: 15.93 mm

  • Tested barrel length 45 cm

  • GFZ mounting post OD: 15.90 mm

  • GFZ mounting post length: 17.35 mm

  • Shroud insertion section: 19.30 mm

  • Retention pin groove: 5.20 mm

  • Raised retention boss: +0.70 mm

Installation

  1. Slide the adapter over the barrel.

  2. Insert the rear portion of the adapter fully into the Lynx 2.1 shroud.

  3. Reinstall the factory front shroud retention pin.

  4. Slide the GFZ 3×5 BCAR onto the front mounting post until the BCAR's internal O-rings securely engage the adapter.

The BCAR does not need to bottom out against the adapter flange to be retained. Its internal O-rings provide the clamping force on the mounting post.

Print Recommendations

The final prototype was designed as a functional blaster component, so I recommend:

  • 0.16–0.20 mm layer height

  • 4–5 walls/perimeters

  • High wall count around the retention area

  • PLA+/PLA Pro, PETG, ASA, ABS, or PC/PC blend depending on your application

  • Print with good dimensional accuracy

Because barrel and printer tolerances vary, verify the fit before forcing the adapter onto your barrel.

If your barrel measures noticeably larger than 15.93 mm OD, the 16.05 mm bore may be too tight.

Development Notes

Several versions were test printed while dialing in:

  • Shroud insertion fit

  • Barrel alignment

  • Stock-pin retention

  • BCAR mounting diameter

  • BCAR-to-flange spacing

  • Overall stick-out

V4.3 is the final physically tested version and is the version I recommend printing.

Disclaimer

This is an independently developed, unofficial accessory.

It is not affiliated with, sponsored by, or endorsed by Orion Blasters, Good Foam Zone (GFZ), Out of Darts, or any other manufacturer or retailer.

Product and brand names are used only to identify compatibility.

Use appropriate eye protection and follow all applicable rules and safety practices when using modified foam-dart blasters.

Tagi