Swappo — One-Handed SD Card Case (No Glue, No Hardware, STEP included)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Pocket SD card case, 25 g. Thumb lever ejects four cards at staggered heights. Snaps together.
- Ocena
- 5 / 5
- Polubienia
- 176
- Pobrania
- 211
- Wydruki
- 6
- Wyświetlenia
- 1901
- Oceny
- 7
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Photo & Video
- Licencja
- Creative Commons — Attribution — Noncommercial — NoDerivatives
25 g · 4 full-size SD cards · no supports
Push the lever with your thumb: Four SD cards step out of the case at different heights, each one easy to reach. Push it back and they disappear. One hand, one motion, no lid to open and drop.
Swappo is a pocket-sized SD card case built for the moment you are holding a camera in one hand and need a fresh card now. It prints in about two hours, uses 25 g of filament, needs no glue and no hardware, and assembles in under a minute.

Assembly and quick tour (video)
No glue. No screws. No heat-set inserts. No magnets.
The parts snap together - that is the whole assembly. Under a minute, and it comes apart again if you want to change the tolerance variant or the back plate.
What it solves
Card cases are boxes with lids. Fine on a table, awkward on location. One hand is already holding a camera, so the other has to open the lid, tip the cards out and fish the right one from a stack, usually while the thing you are meant to be filming is happening.
Swappo works like a dispenser: Thumb on the lever, cards come out, take one, release. The whole sequence runs inside the hand holding the case, and your other hand never leaves the camera.
That is what the staggered heights are for. Every card sticks out a little further than the one behind it, so you can pick out the one you want instead of pulling the whole stack.

Knowing which card is used
Position is the information. Work through the slots in order and always return a card to the slot it came from. Everything behind is shot, everything ahead is empty.
Cards are meant to go in contacts first, so they sit fully enclosed and you take hold of a card by its outer edge. The end your fingers touch is never the end that goes into the camera.
Print settings
Material | PLA (PETG may need different tolerances) |
Layer height |
|
Perimeters |
|
Infill |
|
Supports | none |
Print time | approx. 2 h |
Filament | approx. 25 g |
The whole model was designed with printability in mind, so there ist no support needed.
On PETG: it is the better material if your case lives in a camera bag in a car because PLA starts to soften around 55 °C and a closed car in summer gets there easily. But my tolerance study was done in PLA. PETG shrinks differently, so start with the loose variant and work down. Please share your results!
Before you print: tolerance variants
Printers differ, so your tolerances might be different. The clamping section is the only dimension that decides whether cards sit right, and it is the one thing your printer can shift. So the card block comes in five versions, everything else in the model stays the same.
Version | Use when |
|---|---|
Standard | Start here. Tuned on a Bambu Lab A1, 0.4 mm nozzle, PLA |
Tight | Cards feel a bit loose |
Very tight | Cards feel very loose or fall out when the case is shaken |
Loose | Cards need force to insert |
Very loose | Cards need much force to insert, or your printer runs tight |
Print the standard version first. If the fit is wrong, switch. You do not need to reprint the whole case, only the card block.
If none of the five works on your printer, please leave a comment. Tell me which one came closest and in which direction it missed, and I will generate the STL in between and upload it. The range moves in 0.03 mm steps, so there is room to go finer or further either way.

Files and variants
Full set of printable parts, ready to slice
Five tolerance variants of the card block
Left-hand and right-hand versions — the lever sits where your thumb is (only for project files)
Blank back plate with a flat area for a logo, a name, or a label like "BACKUP 1"
STEP files — so you can change anything you want
How the mechanism works
Everything runs off one single lever. Four ejector fingers of different lengths sit on it, so a single stroke pushes the four cards to four different heights. The staircase effect is not a second mechanism, just four ribs of different length on one part. At rest the lever snaps into a detent with an audible click, so nothing gets triggered by accident in a bag. The lever ratio is 1:1, thumb travel equals card travel. That number is deliberate, and it came out of a failure.

The first working prototype held the cards by a transition fit over the full slot depth, and it ejected them half a metre across the room. The cause was stick-slip: you push against static friction, your finger and the plastic store elastic energy, the friction breaks, and all of it dumps into a 2-gram card.
The fix was geometric rather than a weaker spring or a slower lever, and it is the part of this design I am actually proud of — even though you cannot see it from the outside. Each slot is now stepped: 2.16 mm at the entry, clearly wider than the card, and 2.105 mm over the last few millimetres at the bottom. Nominal card thickness is 2.10 mm, so a card slides in freely almost all the way and only clamps right at the end. There is barely any friction path to break out of, so there is barely any stored energy to release. The cards now travel as far as your thumb does, and stop. A chamfer at the bottom of each slot compensates for elephant foot, so the clamping section keeps its dimension even if your first layer squishes. I found those two numbers by stepping the slot width in 0.03 mm increments and printing the range, not by guessing.

A note on why this matters more than it sounds: real SD cards are not all 2.10 mm. Measured across several brands, the spread is larger than the standard suggests. A single-width friction slot is therefore a lottery — tight with one brand, loose with another. A stepped slot with a short clamping zone is far less sensitive to that spread.
Brand / model | Measured thickness |
|---|---|
SanDisk Ultra 128 GB | 2.15 mm |
SanDisk Ultra 32 GB | 2.10 mm |
Transcend Class 10 16 GB | 2.07 mm |
Transcend Class 10 32 GB | 2.12 mm |
AgfaPhoto 4GB | 2.13 mm |
Nominal (SD standard) | 2.10 mm |
Development
Roughly eight to ten printed prototypes, and two questions that had to be answered separately: how to move the cards, and how to hold them.
The first attempts were sliders, one running along the side and one vertical. Both worked. Both needed so much travel that the case grew past the size that makes it worth carrying in the first place. The lever came out of that constraint: a rotation buys the same card travel in a fraction of the length. After that came a run of experiments with different ways of triggering it, and in the end the plain lever ratio won, simply because it was the most controllable part of the whole mechanism.
Holding the cards took a similar detour. I went through several lid mechanisms before accepting that none of them beat having no lid at all: a light press fit does the same job, needs no second hand, and has nothing to snap off. Making that reliable is what the stepped slot above is for.
The final design is simpler than every version that came before it. Each iteration removed something.

Credit & Feedback
Lever-actuated fan-out mechanisms are well known from slim wallets, and that is where the initial idea came from. The kinematics here are not transferable though: credit cards are thin, flexible and identical, while SD cards are thick, rigid, contact-sensitive and vary in thickness between manufacturers. Everything below the basic idea "a lever presents the contents" had to be solved from scratch, in particular the stepped slot, which exists purely because rigid cards behave differently from flexible ones.
If you print it, please post a Make! :-) I would like to know how the standard tolerance behaves on printers other than mine. If the fit is off on your machine, tell me which variant worked and which printer you used, and I will add it to the description.