1 / 7
Two-Story Gear Tower Fidget — 11 Herringbone Gears, Print-in-Place, No Bearing, No Supports, No Assembly — zdjęcie 1
1 / 7

Two-Story Gear Tower Fidget — 11 Herringbone Gears, Print-in-Place, No Bearing, No Supports, No Assembly

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A two-level planetary gear tower that comes off the build plate already working: 9 separate pieces.

Ocena
0 / 5
Polubienia
4
Pobrania
22
Wydruki
0
Wyświetlenia
100
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

Eleven gears on two floors, one print, zero assembly.

Flick any gear and the whole tower moves — one single degree of freedom running through eleven herringbone gear sections on two levels.

How it is laid out

Ground floor — a sun gear in the middle, three large gears around it, and three small ones filling the gaps. Not a normal planetary: the six outer gears form a closed ring, each small one meshing with the two large ones beside it.

Second floor — the three small satellites carry on upward and drive a big gear on the central axle. That top gear counter-rotates against the sun below it.

Speeds: sun ×1.00 · large gears ×−0.60 · satellites ×1.00 · top gear ×−0.60. The sun and the three satellites spin together while everything else turns backwards, slower.

No bearing, no hardware, no assembly

Every axle, gear and hex cap is printed in place. Nine separate pieces come off the plate already meshed. Nothing to buy, nothing to press in, nothing to glue.

The hex caps are not decoration — each one is the axial retention for its gear, and its chamfer is hexagonal all the way down so it reads as one clean cap.

The central axle carries a 45° conical shoulder halfway up. That shoulder retains the sun from above and gives the big top gear something to sit on. Without it the top gear would rest on the sun, and since the two turn in opposite directions they would rub against each other.

Why these exact tooth counts

They were searched for, not guessed. Three conditions have to hold at once:

  • (Zsun + Zlarge) divisible by 3, or the three large gears will not sit at 120° with the same tooth phase.

  • A closed ring adds one more: each small gear meshes with two large neighbours, and the two tooth phases they demand must agree. With the obvious 10/14 pairing they disagree by 6.2° and the ring will not close — for any small gear size.

  • Second floor: the top gear plus the satellite gear must total 24 teeth, and that sum must also divide by 3.

Sweeping the whole space gives 15 valid combinations, and in almost all of them the small gears have the same tooth count as the sun. This model uses 9 / 15 / 9, so the entire thing is built from just two tooth profiles.

Verified, not hoped

The Python scripts generate the involute profiles (25° pressure angle) and then check the model rather than trust it:

  • Separate pieces: 9 (frame, sun, top gear, 3 large, 3 satellites)

  • Minimum clearance, full rotation: 0.33 mm

  • First layer of every gear: 100 % supported by the frame below it

  • Air gap under each gear: exactly one layer

  • Size: 57 × 57 × 32 mm, ~24 g

The support check is the one that matters and the one that is usually skipped. A slicer flags overhangs by angle, so it says nothing about a first layer printing over a gap — and neither does a render. Every gear's underside is sampled on a 0.3 mm grid and tested against the frame beneath it. An earlier draft of this design had a 1 mm ring of every gear hanging over nothing, and only that test caught it.

Print settings — short but please read

  • Layer height 0.2 mm. Not 0.15, not 0.3. The gap between each gear and the boss under it is one layer. Thicker and the gears fuse to the frame; thinner and you get two layers of air with nothing to sit on.

  • No supports. No brim. Every overhang is 45° or steeper.

  • 3 walls, 10-15 % infill, PLA. About 1 h 15.

Do not scale this model. Scaling shrinks the clearances too: at 75 % the one-layer gap becomes 0.15 mm and the whole thing comes out welded solid. To change the size, regenerate it with the included scripts, which keep every clearance absolute while changing the tooth size.

First spin: hold the frame and turn one gear firmly. Each gear rests on 30-45 mm² of one-layer contact and needs a twist to break free. Work through them one at a time; after that it runs smooth.

Two variants

  • Tower-Gear-Spinner.stl: plain waist between the two floors — this is the printed and tested one

  • Tower-Gear-Spinner-continuous.stl: the satellite teeth run unbroken from bottom to top, in three stacked chevrons

Same mechanism and same clearances; the second is purely how the satellites look between the floors.

Multi-colour without assembly

Insert a filament change in your slicer (right-click the layer in preview):

  • z = 2.6 mm: frame done → ground-floor gears start

  • z = 16.8 mm: second floor and the big top gear start

Remix it

generator.py writes the OpenSCAD file, gear_profiles.py computes the involutes, and verify_print_in_place.py checks any print-in-place STL: how many pieces actually came out separate, the real 3D clearance between each pair, and whether every moving part's first layer has something under it. Change the tooth counts, run it, and it verifies the mesh through a full rotation before writing anything.

No non-printed parts. Nothing at all.

Tagi