1 / 6
Samsung 25W Magnetic Wireless Charger Stand – 60° Heavy-Duty Desk Stand — zdjęcie 1
1 / 6

Samsung 25W Magnetic Wireless Charger Stand – 60° Heavy-Duty Desk Stand

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Rigid 60° stand for Samsung’s 25W magnetic wireless charger, with cable routing and an EPDM anti-slip base.

Ocena
0 / 5
Polubienia
2
Pobrania
15
Wydruki
0
Wyświetlenia
71
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial

Samsung 25W Magnetic Wireless Charger Stand – 60° Heavy-Duty Desk Stand

Summary

Rigid 60° stand for Samsung’s 25W magnetic wireless charger, with cable routing and an EPDM anti-slip base.

Description

A simple and heavy-duty desktop stand designed for the Samsung 25W magnetic wireless charger.

The stand holds the charger at a fixed 60° angle, allowing a phone to be attached magnetically without requiring a conventional lower phone support. The design focuses on high rigidity, simple construction, easy FDM printing, and stable everyday use in an office environment.

The body consists of two separately printed parts that are permanently bonded together. The wide structural section and long rearward base provide high resistance against tipping or sliding when attaching, using, or removing the phone.

Design Features

  • Fixed 60° viewing angle

  • Designed for Samsung 25W magnetic wireless charger

  • Magnetic attachment allows portrait or landscape phone orientation

  • Thick, rigid structure for long-term desk use

  • Long base extends behind the phone to provide a large support moment

  • Integrated cable-routing channel

  • Two-part construction optimized for FDM printing

  • Rounded exterior surfaces for a clean desktop appearance

  • No hinges, moving parts, or adjustment mechanisms

  • Designed for simple and durable everyday use

The rear portion of the base extends significantly beyond the phone position. This increases the effective support length and provides substantial resistance against the force generated when pressing the phone or removing it from the magnetic charger.

A 2 mm thick × 20 mm wide EPDM rubber strip is installed underneath the base. This increases friction with the desk, reduces sliding during magnetic attachment/removal, absorbs small surface irregularities, and protects the desk surface.


Assembly Instructions

1. Join the Two Printed Parts

The stand is printed as two separate structural parts.

Check that both mating surfaces fit correctly, then permanently bond the two parts together using a suitable adhesive.

Apply the adhesive evenly across the mating surfaces and firmly clamp or hold the parts in their final position until the adhesive has fully cured.

Because the joint has a relatively large bonding area and the stand uses a thick structural geometry, the completed assembly forms a very rigid support structure.


2. Prepare the Charger Mounting Surface

The rear surface of the circular charger pocket can be lightly finished with a thin layer of resin if necessary.

The purpose is only to create a flat and uniform contact surface for the charger.

Do not significantly build up the side walls of the charger pocket, as the original printed dimensions are intended to maintain the correct mounting clearance.


3. Apply 0.8 mm 3M Foam Tape

Before installing the wireless charger, apply 0.8 mm thick 3M foam tape to the surface where the rear of the charger contacts the stand.

The foam tape serves several purposes:

  • Secures the wireless charger in position

  • Compensates for small FDM surface irregularities

  • Reduces minor movement and vibration

  • Provides uniform contact pressure

  • Prevents the charger from moving inside the mounting pocket

Keep the side walls of the charger mounting area unchanged so that the printed geometry continues to provide lateral positioning.


4. Install the Wireless Charger

Route the charger cable through the integrated cable opening first.

Carefully position the charger inside the circular mounting area and press it evenly against the 0.8 mm 3M foam tape.

Make sure the charger is centered and fully seated before applying firm pressure.

The charger cable should pass naturally through the vertical opening without being sharply bent or pinched.


5. Install the EPDM Anti-Slip Strip

Attach a 2 mm thick × 20 mm wide EPDM rubber strip to the underside of the stand.

Clean the bottom surface before installation to ensure good adhesion.

The EPDM strip provides:

  • Increased friction on the desk

  • Resistance to sliding when removing the phone

  • Vibration damping

  • Compensation for minor surface unevenness

  • Protection against scratches


Structural Concept

The stand does not rely only on its weight to remain stable.

The base extends a considerable distance behind the phone and charger, producing a long support lever arm against the forces generated during normal use. Combined with the wide base and high-friction EPDM strip, this gives the stand substantial resistance to both sliding and overturning.

The overall design intentionally avoids thin arms, hinges, adjustable joints, and other potential failure points.

The result is a simple, rigid, and practical magnetic charging stand intended for repeated everyday desk use.

Additional Tags

samsung wireless-charger 25w magsafe magnetic-charger phone-stand charging-stand desk-stand smartphone office epdm 3d-printing

Tagi