1 / 4
FluxDock M4 - Crossed-Ribbon MacBook Air Stand — zdjęcie 1
1 / 4

FluxDock M4 - Crossed-Ribbon MacBook Air Stand

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A stable one-piece vertical dock with opposing sculpted ribbons for 13-inch and 15-inch MacBook Air M4.

Ocena
0 / 5
Polubienia
1
Pobrania
13
Wydruki
0
Wyświetlenia
54
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Computers
Licencja
Standard Digital File License

FluxDock M4 is a sculptural one-piece vertical dock for MacBook Air. Two opposing support ribbons rise in opposite directions, producing a distinctive crossed silhouette while distributing contact across four diagonal support zones.

The wide two-level base keeps the dock visually low and stable. A recessed floor strip, protected inner faces and four positions for non-slip feet make the design practical for everyday desk use.

FEATURES

• Original opposing-ribbon design
• One-piece construction
• No supports required
• Approx. 194 × 104 × 52.5 mm
• 14.9 mm bottom slot and 17.6 mm upper opening
• Recessed central strip for protective felt
• Four recessed positions for optional 12 mm rubber feet
• High-resolution closed manifold STL
• Designed for normal FDM printing — not Vase Mode

COMPATIBILITY AND FIT

FluxDock is designed for bare 13-inch and 15-inch MacBook Air M4 models.

• MacBook Air 13-inch M4 body thickness: approximately 11.3 mm
• MacBook Air 15-inch M4 body thickness: approximately 11.5 mm
• Recommended side felt: 0.75 mm on each inner rail face
• Effective padded bottom opening: approximately 13.4 mm

This leaves practical clearance without allowing excessive movement. Cases, hard-shell covers and thick skins are not included in the fit allowance. Measure your device and the actual felt before printing if you use a different laptop.

PROTECTIVE PADS

Apply soft 0.75 mm adhesive felt to both inner rail faces and to the recessed strip beneath the laptop. Install four non-slip rubber feet in the 12 mm underside recesses before use. Do not place a laptop directly against unfinished printed surfaces.

PRINT INSTRUCTIONS

Recommended setup:

• Orientation: flat on the supplied base
• Nozzle: 0.4 mm
• Layer height: 0.20 mm; use 0.16 mm for a finer surface
• Line width: 0.42–0.46 mm
• Walls/perimeters: 4 recommended
• Top solid layers: 5
• Bottom solid layers: 6
• Infill: 15–20% gyroid or adaptive cubic
• Supports: none
• Brim: normally unnecessary; optional 4–6 mm if adhesion is unreliable
• Outer-wall speed: 35–45 mm/s
• First-layer speed: 15–25 mm/s
• Seam: place on the rear or least visible side
• Wall generator: Arachne/variable-width is recommended when available

The only intentional bridges are the four short 12 mm ceilings above the rubber-foot recesses. A normally calibrated bridge profile should print them without support material.

DEVIL DESIGN PET-G STARTING PROFILE

• Nozzle: 230–240 °C; start at 235 °C and follow the range printed on your spool
• Bed: 70–80 °C; start at 75 °C
• Cooling: 30–50% after the first layers
• Retraction: use the calibrated PET-G value for your printer
• Dry the filament if stringing, bubbles or a rough surface appear

Avoid excessive first-layer squish so the rounded lower edge stays clean.

DIGITAL VALIDATION

The supplied STL has been checked as one closed manifold component with zero boundary and zero non-manifold edges. The geometry is support-free in the supplied orientation, apart from the four intentionally short foot-recess bridges described above.

A first physical test print is still recommended before long-term use. Stability calculations and digital fit checks do not replace verification with the actual printer, material, felt and laptop.

LICENSE

This model is provided under the Standard Digital File License selected for this listing. For commercial licensing inquiries, contact the creator through the Printables profile.

Tagi