1 / 4
Digital ClockClock 24 — a kinetic clock made of 24 little analogue clocks (LCD build) — zdjęcie 1
1 / 4

Digital ClockClock 24 — a kinetic clock made of 24 little analogue clocks (LCD build)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Case for a 24-screen ClockClock: the hands sweep into position to form the digits, then dance. Full and split-for-smalle

Ocena
0 / 5
Polubienia
6
Pobrania
8
Wydruki
0
Wyświetlenia
175
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Wall-mounted
Licencja
Creative Commons — Attribution

A ClockClock 24 is a digital clock built out of twenty-four little analogue ones. The hands sweep into position to form the digits, hold them for a minute, then break formation and do something else entirely before sweeping back. The original by Humans since 1982 is beautiful and costs thousands; this is the same idea for about €210, using 24 round LCD panels instead of 48 motors.

Finished it is 27 × 13 cm and 730 g, and hangs on two screws.

Video of it running

Full project info can be found here: https://tuct.github.io/esphome-lvgl-clock/

WHAT TO PRINT (24-SCREEN VERSION)

One part: a face plate with 24 round cutouts and a tray behind it that holds the eight carrier boards at the right spacing.

  • ClockClock24_full.obj — the whole case in one piece, 365.5 × 149 × 40 mm. Needs a Prusa XL bed or bigger, and at 365.5 mm it is longer than the XL's 360 mm axis, so rotate it 45° on the plate.

  • ClockClock24_a.obj + ClockClock24_b.obj — the same case in two halves, 183 × 149 × 40 mm each. Fits a 250 × 210 bed comfortably. Print both and join.

  • clockclock24.f3d — Fusion 360 source, if you want to change it.

HOW TO PRINT IT

Face down on the plate, no supports. The visible face prints against the build sheet, so whatever texture that sheet has is the finish you get on the front.

Print it opaque — this is the setting that matters, and it is not about strength. The panels are backlit: a case that lets light through glows around every cutout instead of showing 24 clean discs on black.

- Enough top and bottom layers to fully close the surface — more than the slicer default. One thin spot is a visible bright patch.

- Solid infill for the walls. The vertical faces between the cutouts are thin, and sparse infill there leaks light from one panel into its neighbour.

- Dark filament helps but does not replace either of those. Thin black PLA still glows.

Nothing structural, no fine detail, any material you like.

WHAT ELSE YOU NEED

The case is the easy part. The 24-screen build:

  • 24 × 1.28" round GC9A01A LCD panel, 240×240 — https://amzn.to/4xJpK79 (5-pack ~€23.50, buy 5) — €118–140

  • 8 × Seeed XIAO ESP32-S3 — €45–122, and the one row worth shopping. Buy 3-packs direct from Seeed at ~€15 for three rather than ~€15 each on Amazon: https://www.seeedstudio.com/Seeed-Studio-XIAO-ESP32S3-3PCS-p-5919.html. Saves about €77.

  • 8 × custom carrier PCB — one fab order, €20–30. Gerbers in the repo.

  • MP1584EN buck modules, headers, connectors, caps, one 5 V 2 A supply — under €50 together.

Roughly €210 all in, up to €374 buying everything the expensive way.

The panels hot-glue into the case, the carriers push onto their headers, and one 4-pin cable per hop chains the lot together.

The 4-screen version:

Roughly €70–160, mostly depending on where the panels come from.

Firmware is ESPHome. One board has Wi-Fi and broadcasts the time to the other seven down a single wire, so all 48 hands stay on the same millisecond.

Full build guide, costed BOM, PCB gerbers and firmware: https://github.com/tuct/esphome-lvgl-clock

ALSO HERE: THE 4-SCREEN VERSION


If 24 panels is too much, there is a cheaper build using four rectangular screens, one per digit, each drawing six mini-clocks. Roughly €70–160 and an afternoon rather than a project. The trade is spacing: the gaps between the digits end up wider than the gaps between the clocks inside them, so it reads as four blocks rather than one field of clocks.

  • ClockClock24_4screen_Body.obj — the body, 237.9 × 109.8 × 33 mm.

  • ClockClock24_4screens_Blocker.obj — a light blocker that sits inside. Print this one in black and you can have the outer case in white or any colour without the panel light glowing through the walls and seams.

  • ClockClock24_4Screens.f3d — Fusion 360 source.

Same print advice: face down, no supports, enough top and bottom layers, solid walls.

Try the clock in your browser before printing anything — same engine as the firmware, nothing to install: https://tuct.github.io/esphome-lvgl-clock/

Tagi