Irrigatia 13 mm coupler with 3 mm dripper takeoff | Spojka 13 mm s odbočkou pro Irrigatia
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
13 mm hose coupler with a built-in 3 mm dripper takeoff for Irrigatia solar irrigation systems.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 3
- Wydruki
- 0
- Wyświetlenia
- 35
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Outdoor & Garden
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
A 13 mm hose coupler that doubles as a 3 mm dripper takeoff, for Irrigatia solar irrigation systems.
In the stock system, joining two lengths of 13 mm supply hose and branching off a 3 mm dripper line are two separate jobs needing two separate fittings. This part does both at once: cut the supply hose wherever you want a dripper, push both ends onto the barbs, and take the 3 mm line straight off the side.
No punching into the pipe wall. Punched takeoffs are the usual weak point — the hole works loose over a season or two and starts weeping, and once a hole is in the pipe it's there for good. Here the branch is part of the joint itself.
Print as many as you like as the beds grow.
Compatibility
Made for Irrigatia solar systems (SOL-C18Q, C36Q, C60, C120, C180 and the extension kits) using 13 mm supply hose and 3 mm dripper tube.
Generic drip irrigation kits on the same tube sizes should work too, but hose OD varies slightly between brands — measure yours before printing a batch.
⚠ Low-pressure systems only. Irrigatia pumps from a water butt or tank at very low pressure, which is what makes a printed fitting viable here. Do not use this on mains water pressure. A printed part on a mains line is a burst waiting to happen, and it will happen while you're away.
File
irrigatia_coupler_3mm_takeoff.stl — one part, one 3 mm takeoff. Print as many as you need.
Print settings — watertightness matters more than strength here
Material: PETG. Handles sunlight and frost far better than PLA, which goes brittle outdoors within a season. ASA also works if you can print it.
Layer height: 0.1 mm
Perimeters: 6, and check in the slicer preview that the walls actually meet with no gap down the barb
Infill: 20 % (the perimeters do the sealing, not the infill)
Flow: 103 %. Slight over-extrusion closes the micro-gaps between perimeters. This is the single biggest factor in whether it leaks.
Cooling: reduce or switch off after the first few layers — cooler layers bond worse, and poor layer bonding is where water finds its way out
Speed: slower than usual, especially on the perimeters
Supports: none needed
Orientation: standing upright, 13 mm barbs vertical — the layers then run around the tube rather than along it
Fitting
Cut the 13 mm supply hose where you want the dripper.
Warm both hose ends in hot water for a few seconds — they slide onto the barbs far more easily and grip harder once cool.
Push both ends fully home, past the last barb.
Push the 3 mm dripper tube onto the side takeoff.
Secure the 13 mm joints with a small hose clip or a cable tie. Not strictly needed at this pressure, but it costs nothing and stops a joint creeping apart in summer heat.
Run the system and check the joint for weeping before you walk away.
If a printed part does weep slightly, a smear of silicone grease on the barbs usually settles it. If it weeps from the body rather than the joint, the print isn't watertight — raise flow and cut cooling, don't try to seal it from the outside.
Not affiliated with or endorsed by Irrigatia Limited. The brand and product names are given for identification only.
