Two-Piece Magnetic Galaxy Z Fold 8 Adapter for GameSir G8+ | Case and Hinge-Protector Compatible
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Case-friendly Z Fold 8 adapter for GameSir G8+, with hinge clearance, magnets, charging access and a 10° tilt.
- Ocena
- 0 / 5
- Polubienia
- 8
- Pobrania
- 119
- Wydruki
- 0
- Wyświetlenia
- 1055
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Video Games
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
This two-piece magnetic adapter lets you comfortably use a Samsung Galaxy Z Fold 8 with a case inside the GameSir G8+ controller.
The open center provides clearance for many cases with hinge protection, while the separate left and right supports hold the phone securely. It was designed and physically tested using the Ringke Onyx Flap case shown in the photos, but it should work with many other cases that have a similar thickness and edge profile.
One of the adapter’s most important features is its 10-degree player-facing viewing angle. Instead of holding the screen flat against the back of the controller, the adapter tilts the phone approximately 10 degrees toward you. This creates a more natural viewing position and makes the setup noticeably more comfortable during longer gaming sessions.
Features
10-degree player-facing angle: Tilts the screen toward you for better visibility, ergonomics, and comfort.
Case-friendly design: Allows you to use the Galaxy Z Fold 8 without removing its case.
Hinge-protector clearance: The open center leaves room for raised hinge protection and folding hinge flaps.
Cover-display mode: Rotate the folded phone to play using the outer display.
Inner-display mode: Unfold the phone and use the full inner display for a larger handheld gaming experience.
Camera clearance: A dedicated relief provides room for the camera bump when using the cover display.
USB-C charging access: A charging-port cutout allows the phone to remain connected to a charger while using the inner display.
Magnetic two-piece construction: Four press-fit 6 × 3 mm magnets align the two halves and help hold them together.
Secure controller fit: Small ribs on the sides index into the matching ribs inside the GameSir G8+.
Firm retention: The adapter fits securely enough to remain seated when the controller is moved or shaken.
Battery-friendly parked fit: With only the adapter installed, the controller does not need to extend far enough to switch itself on.

Improved 10-Degree Viewing Angle

The phone does not sit flat against the back of the GameSir G8+. The adapter intentionally angles the display approximately 10 degrees toward the player.
Holding the screen completely flat felt awkward because the display faced upward instead of toward the player’s natural line of sight. Tilting it toward the user makes the screen easier to see while holding the controller normally.
This small change noticeably improves the ergonomics and makes the complete setup feel more like a purpose-built handheld gaming system.
Cover-Display Mode

The adapter can hold the phone while it is folded, allowing you to play using the Galaxy Z Fold 8’s cover display.
Rotate the phone into the appropriate position and place it across the two adapter halves. The camera relief provides clearance for the raised camera area so the phone can sit correctly without the camera bump interfering with the adapter.

Inner-Display Mode

Unfold the phone and place it across both adapter halves to use the full inner display.
The open space between the two pieces provides clearance for the case’s hinge protection. This allows the phone to remain inside its case while using the larger folding display.
The USB-C cutout also keeps the charging port accessible, allowing you to charge the phone during longer gaming sessions.

Case Compatibility
This adapter was designed and physically tested with:
Samsung Galaxy Z Fold 8
Ringke Onyx Flap case
GameSir G8+ Bluetooth controller
The Ringke Onyx Flap is the case shown throughout the photos.

Because the adapter uses two separate supports with an open center, it should work with many other Galaxy Z Fold 8 cases, including most cases with hinge protection. Compatibility will depend on the case’s overall thickness and the shape of its edges where they contact the adapter.
Case thickness, corner profiles, camera surrounds, and hinge-protector dimensions vary between manufacturers. Cases that have not been physically tested cannot be guaranteed, but the open-center design should provide much broader compatibility than a single-piece holder.
Upcoming TORRAS Case Testing
I will test compatibility with a TORRAS case once it arrives. TORRAS compatibility is currently unconfirmed, but the open-center design should give its hinge protection room to clear.
The TORRAS case also has a built-in stand. If it fits as expected, this could provide an additional portable gaming configuration. The unfolded phone could be placed on a table using the integrated stand while the GameSir G8+ is used as a separate Bluetooth controller.
This would create a compact tabletop setup similar to playing a Nintendo Switch in tabletop mode.
Required Hardware
Left adapter half
Right adapter half
Four 6 × 3 mm disc magnets
A small amount of super glue
Installing the Magnets
The magnet pockets are designed as a tight press fit. The magnets may remain in place without adhesive, but I recommend placing a small drop of super glue into each pocket before press-fitting the magnets for additional security.
Because the fit is tight, pressing the magnets into place using only your fingers may be difficult. The easiest method is to place each magnet on a solid table and press the printed part down onto it.
Check the polarity of all four magnets before applying glue.
Arrange them so the magnets in the completed adapter halves will attract each other.
Mark the correct face of each magnet if necessary.
Place one magnet flat on a solid table or work surface.
Add a small drop of super glue to the corresponding magnet pocket.
Align the printed part directly over the magnet.
Press the printed part downward until the magnet is fully seated.
Repeat for the remaining magnets, checking the polarity before installing each one.
Allow the super glue to cure before joining the two halves.
Double-check the polarity before every press fit. The magnet pockets are intentionally tight, so removing a magnet installed in the wrong orientation may be difficult.
Final Assembly and Use
Install all four magnets and allow the adhesive to cure.
Bring the two adapter halves together and confirm that the magnets attract.
Place the assembled adapter inside the GameSir G8+.
Align the adapter’s side ribs with the ribs inside the controller.
Confirm that the adapter is firmly seated.
Insert the phone in the appropriate orientation for the cover or inner display.
When using the inner display, position the phone so its USB-C port remains accessible through the charging cutout.
The adapter should fit firmly inside the controller without falling out during normal movement. When the phone is removed, the adapter can remain seated without extending the GameSir G8+ far enough to switch it on.
I've included the step file so feel free to make edits and adjust it for your use.
