1 / 6
Magnetic Fishing Rod Holder (Car/Metal) — zdjęcie 1
1 / 6

Magnetic Fishing Rod Holder (Car/Metal)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

3D-printable magnetic fishing rod holder for mounting on metal surfaces (car roof, trailer, boat, workshop shelving, etc

Ocena
0 / 5
Polubienia
1
Pobrania
3
Wydruki
0
Wyświetlenia
33
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Organizers
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

Function The holder attaches to any ferromagnetic surface — car roof, sheet steel, trailer, tool cabinet, etc. — via two embedded neodymium magnets (10x10x10 mm). The fishing rod is placed into the 20 mm opening secured with the rubber band, preventing it from falling out or shifting during on/offload or transport.

Required hardware (not included in the print)

  • 2x neodymium magnets, 10x10x10 mm

  • 1x rubber band 30cm, approx. 3–4 mm thick (to secure the rod)

  • Super glue (cyanoacrylate), to attach the TPU foot

Assembly

  1. Insert both neodymium magnets into the designated recesses.

  2. Glue the green foot (TPU print) to the underside of the holder using super glue.

  3. Fit the rubber band used to secure the rod.

  4. Place the holder on the desired metal surface, insert the rod, and secure it with the rubber band.

Alternative mounting The magnets can be removed at any time through the access holes on top. The same holes can alternatively be used to screw the holder permanently in place — e.g. onto wooden walls, in a garage, or on a dock — for a fixed, non-magnetic installation.

Compatibility The holder's opening is 20 mm wide. Depending on the mounting height/position, the holder fits nearly all common rod shapes and diameters.

Material note The foot must be printed in TPU (flexible) so it conforms to the mounting surface without scratching it. The main frame is intended to be printed in a rigid material (e.g. PETG/ABS).

Genaue Beschreibung (DE)

Funktion Der Halter wird mittels zweier eingesetzter Neodym-Magnete (10x10x10 mm) auf eine ferromagnetische Fläche gesetzt, z. B. Autodach, Stahlblech, Anhänger oder Werkzeugschrank. Die Angelrute wird in die 20 mm große Öffnung gelegt und das Gummiband sichert diese, sodass sie beim Montieren, Fahren oder Transport nicht herausfallen oder verrutschen kann.

Benötigtes Zubehör (nicht im Druck enthalten)

  • 2x Neodym-Magnete, 10x10x10 mm

  • 1x Gummiband 30cm, ca. 3–4 mm stark (für die Rutensicherung)

  • Sekundenkleber (Cyanacrylat), zum Fixieren des TPU-Fußes

Montage

  1. Beide Neodym-Magnete in die dafür vorgesehenen Aussparungen einsetzen.

  2. Grünen Fuß (TPU-Druck) mit Sekundenkleber auf die Unterseite des Halters kleben.

  3. Gummiband zur Rutensicherung anbringen.

  4. Halter auf die gewünschte Metallfläche setzen, Rute einlegen und mit dem Gummiband sichern.

Alternative Befestigung Die Magnete lassen sich über die von oben zugänglichen Löcher jederzeit wieder entnehmen. Über dieselben Löcher kann der Halter alternativ auch fest verschraubt werden – z. B. an Holzwänden, in der Garage oder am Bootssteg – für eine dauerhafte, nicht-magnetische Montage.

Kompatibilität Die Öffnung im Halter ist 20 mm breit. Je nach Anbauhöhe (Montageposition am Fahrzeug/Objekt) passt der Halter für nahezu alle gängigen Angelrutenformen und -durchmesser.

Materialhinweis Der Fuß muss in TPU (flexibel) gedruckt werden, damit er sich der Auflagefläche anpasst und diese nicht verkratzt. Der eigentliche Halterahmen ist als starres Material (z. B. PETG/ABS) vorgesehen.


PETG and TPU, 20% Infill, no support, Print Position as shown

Tagi