Leg Saver Heat Shield - Triumph Scrambler 1200 XC/XE 2019 Motorcycle (ASA, one bolt)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Outboard exhaust shield that takes the manifold heat off your shin. One OEM bolt, 12 mm air gap, two-colour badge.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 6
- Wydruki
- 0
- Wyświetlenia
- 58
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Attribution — Noncommercial — Share Alike
An outboard heat shield for the right-hand exhaust on a 2019 Scrambler 1200 XC 2019-2021.
It stands 12 mm off the OEM finned cover on the bolt that's already there, and the air gap is the whole thing - nothing on it touches anything hot. 2019 is Euro 4, cat in the header rather than the silencer, which is why that year cooks your shin.
The wordmark is a separate two-colour badge that epoxies into a slot. Blank plate in the files if you'd rather not
Fitment
2019 XC, VIN up to AD7675. The inner face is moulded to the two bulges of the OEM cover kit and the fiche splits those at AE9098 - later bikes will bolt on, they just won't nest. XE should be fine, same exhaust fiche, but I don't have one to try.
One M5 through the standoff boss into the OEM shield's own mount point. Longer than stock, since you're adding 12 mm of boss to the stack. There's an anti-rotation foot at the far end solved to the same height as the boss, so it can't rotate or droop on a single bolt.
Files
- 1_shield - oriented outer face up. The badge slot has to open upward, so don't let the slicer flip it.
- 2a / 2b - the badge. Load them together as one object, two parts. Separately, the red drops to the plate and prints on its own.
- 2c - blank plate, no wordmark.
- cc2-3mf - Centauri Carbon 2 projects, one per job.
Mesh model, so no STEP.
Printing
Shield, ASA: 0.20, 4 walls Arachne, 25% gyroid, tree supports, 12 mm brim, 270 nozzle, 110 bed on the textured plate, fan 0-15%. Iron the top surfaces and drop top surface speed to 60 - the face over the badge is deliberately flattened so there's something to iron, and at 200 those shallow bands never get up to speed. 12h50, 158 g with supports.
Badge, PLA: 0.20, 3 walls, 100%, no supports, ironed, 5 mm brim, 210/60. 46 min, 12 g for both colours.
ASA rather than PETG - sun-exposed and next to an exhaust. Unfilled, not CF: this panel takes knocks and CF gives up around 3% elongation.
The warp risk here is thermal, not adhesion, so it's the 110 bed and a 30 minute soak with the door shut that matter rather than glue. Cool it on the bed.
Hardware
One M5, measured to suit. A few grams of epoxy.
Optional 2 mm leather contact-bonded to the inside face - it's the thermal liner and it covers the support witness. Gold foil tape on the leather's hot face if you want the radiant barrier, shiny side into the gap or it does nothing.
Fitting
Badge goes in flush: 0.2 mm behind it for the epoxy, 0.2 per side around it. Don't clamp it hard or you'll push the glue out and it'll sit proud.
Then the one bolt. Snug - it's a printed boss. If the plate rocks, shim the foot.
Disclaimers!
Trademark Disclaimer: Triumph names and logos belong to Triumph Motorcycles Ltd. This project is an unofficial fan creation with no endorsement or affiliation. If you'd rather not have it, 2c is the same plate with nothing on it.
Safety Disclaimer:
I present these files as is and accept no responsibility for your use of them on your bike. Don't print the shield in PLA.