1 / 7
FieldClip – Snap-Fit Belt Holster for Zippo — zdjęcie 1
1 / 7

FieldClip – Snap-Fit Belt Holster for Zippo

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

PETG belt holster for standard Zippo lighters, with snap-fit tabs, an integrated clip and a push-out base.

Ocena
0 / 5
Polubienia
2
Pobrania
12
Wydruki
0
Wyświetlenia
41
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

A dedicated place for your lighter

FieldClip is a compact, single-piece belt holster designed around a standard-size Zippo lighter. Two flexible side tabs provide snap retention, while the integrated J-clip attaches the holster to your belt without separate screws, magnets or straps.

This is the V4 design, with a full, uninterrupted belt clip and an open centre section in the base for pushing the lighter upwards.

Features

  • Two flexible retention tabs: rounded inward-facing detents are designed to hold the closed lighter at its upper edge.

  • Integrated belt clip: a full J-shaped clip with a lower retaining lip. The clip itself has no semicircular cut-out.

  • Finger-assisted removal: the open centre of the base provides access underneath the lighter. Two side shelves support it from below; there is no central drain-hole panel.

  • Lower access cut-outs: rounded openings in the front and rear body walls; the rear opening sits behind the full belt clip.

  • Upper thumb cut-out: exposes the lighter for gripping once it has been pushed upwards.

  • Rounded outer body and clip edges: a compact shape for everyday belt carry.

  • Single printed part: no assembly or additional hardware required.

Compatibility and size

Item

Design dimensions

Intended lighter

Standard-size Zippo, approximately 57.2 × 38.1 × 12.7 mm (H × W × D)

Nominal body cavity

38.9 × 13.5 mm (W × D), excluding retention protrusions

Overall holster

Approximately 60.9 × 42.9 × 24.5 mm (H × W × D), including clip and detents

Belt allowance

Designed around belts up to 50 mm wide and 4.5 mm thick; check actual fit

Compatibility with Zippo Slim, Armor, unusual finishes and other lighter sizes is not verified. Measure your lighter before printing. Print at 100% scale; uniform scaling also changes the clip and flexible tabs.

Print instructions

These are suggested starting settings, not a verified printer-specific profile.

Setting

Starting point

Material

PETG

Nozzle

0.4 mm

Layer height

0.20 mm

Perimeters / walls

4

Infill

20% Gyroid

Top / bottom solid layers

5 / 5

Orientation

Upright, base on the build plate, opening facing up

Brim

6–8 mm; keep the clip gap clear

Supports

Designed to print without supports; inspect the lower arches and clip bridge in your slicer and confirm with a test print

Temperatures

Use a calibrated PETG profile appropriate to your filament and build plate

The thin walls, clip and tabs are mostly formed by perimeters, so wall quality and layer bonding matter more than high infill. Keep seams away from the flexible tabs where possible. Remove brim and stringing from the relief slots before flexing them.

In PrusaSlicer, select your actual printer, nozzle and PETG preset, import the STL in millimetres and check the sliced preview. In particular, check that the retention slots and belt-clip gap remain open. Print time and material consumption depend on your sliced setup; no measured print time or verified G-code is supplied.

Using the holster

  1. Check that both tabs and the belt clip can flex freely.

  2. Insert the closed lighter from the top until it seats on the two base shelves. Do not force an excessively tight fit.

  3. To remove it, push upwards through the open base, then grip the exposed top and withdraw it.

  4. Test retention over a soft surface before wearing it. Recheck the clip and tabs periodically for cracks or permanent deformation.

PETG is the intended material for the flexible features. Other materials have not been validated. Remove the lighter from the holster before lighting it; do not expose the printed part to flame or leave it against a hot lighter.

Files and images

The supplied STL is the final V4 geometry. The accompanying images are CAD renders of that same STL, not photographs of a printed part. Physical fit, retention force and long-term durability depend on the lighter, filament and printing conditions and must be checked on the actual print.

Zippo is referenced only to describe intended compatibility. This is an independent accessory design and is not affiliated with or endorsed by Zippo.

Share your make

Printed one? Share a Make with your printer, material and fit feedback — especially how the retention feels with your lighter. Photos showing the belt clip and push-out opening are particularly helpful.

Tagi