1 / 9
Flipsky 85135 motor & 75350 ESC outboard mount — zdjęcie 1
1 / 9

Flipsky 85135 motor & 75350 ESC outboard mount

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A collection of models to mount Flipsky 85135 & optionally Flipsky 75350 ESC on the standard boat transom

Ocena
0 / 5
Polubienia
2
Pobrania
6
Wydruki
0
Wyświetlenia
78
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Public Domain

A collection of models to mount Flipsky 85135 motor & Flipsky 75350 ESC on the standard boat transom. It has cooling channels for the water to flow along the motor. The motor casing on the photos is a bit older and cruder in comparison to the ones uploaded here, but essentially the same.

Additionally you'll need:

  • A transom attachment

  • Propeller

    • I've used the aluminium one that Flipsky sells, but it's a bit unbalanced (both of the 2 that I bought), YMMV. Overall this motor has a shaft/splines that match Yamaha <6hp motors from year 1992 onwards, so there's some choice of propellers.

  • Battery

    • Here it all depends on your requirements, but I went for 20S13P Lithium Ion @ 84v

  • Thick aluminium or normal stainless steel pipe with 28mm outer diameter

    • I've used some stainless water pipe from the local shop

  • 22mm pipe for a steering handle. 20mm also works but you might want to print a spacer to fit the throttle nicer (or just add some thick shrinkwrap)

  • ADC throttle handle with Hall sensor from some bicycle or a scooter, preferably with a button for reverse

  • Some magnetic or normal kill switch, like this one. The throttle linked above it self-stopping, so if you fall out - the boat won't go anywhere, but if you use some Cruise Control, then the kill-switch is a must

  • If you want to mount an ESC - some waterproof junction box, here the one with dimensions 270x133x105mm fits the Flipsky 75350 very nice (pick transparent lid if you want to have a screen on the inside, see below). Or you can print one, but I was lazy to draw it - and waterproofing prints is another topic...

    • There's a mounting plate for the top of the pipe for this junction box included.

    • Actually the ESC comes waterproofed, but I thought it's nicer to have a box for wiring around it, plus the screen/ESP32/etc in there.

  • Heat inserts: 10x M6x9.5x9 (M6x9x9 should also work)

  • Stainless bolts / nuts / washers:

    • 10x M6x25 countersunk - outside ring of motor mount

    • 6x M6x20 countersunk - inside ring of motor mount

    • 4x M5x30 flat top - to mount cone to the motor

    • 4x M8x60 flat top - to attach motor mount to the tube + 1 more if you want to mount the ESC

    • 2x M6 flat top (forgot the length) to mount the steering handle

  • Wires: I've used 6AWG to the battery, but depending on the current maybe 4AWG would be a wiser decision

  • Waterproof cable glands (for the ESC box), cable lugs, etc

  • Optionally if you want monitoring of the VESC:

    • ESP32 (any will do I guess)

    • Some display (I've used 2.42" OLED)

    • CAN module like TJA1051T/3 (preferred since it's 3.3v) or MCP2551 - I had this one, but needs a voltage divider to bring down 5v to ESP32's 3.3v. Probably UART would also work with VESC, but I use a Bluetooth module and not sure how that would interact with the 2nd UART.

    • Some U-Blox-compatible GPS module to measure the speed

    • The firmware for the ESP32 is here

Printing:

  • Use PETG (or, better, PC/ABS/Nylon but harder to print), not PLA

  • I've printed in PETG with an infill of 80%, but probably that's an overkill - just the motor casing itself (the biggest part) was almost 2 kg and printed for 3 days. But I guess given the motor weighs almost 4 kg it's not that bad

Assembly:

  • Cut the pipe to the length that you need, mine was about 120cm I think

  • Drill four 8mm holes in the pipe: first one 20mm from the end of the pipe and then 25mm apart. Use drilling machine to make sure they're centered.

  • Drill another 8mm hole on the other side of the pipe (30mm from the other end) if you want to mount an ESC there

  • Cut using angle grinder (or any other suitable tool) two windows for the cables, grind them so that the cables are not damaged. I've also used a thick shrinkwrap around the cables as an additional protection.

  • Pass cables through the rear motor cone & the pipe, attach & assemble motor mount, silicone the holes if you want

  • If you add ESC:

    • Drill the holes in the junction box for the waterproof glands (phase wires, temp sensor, battery wires, throttle, kill switch etc).

    • Attach the box to the mounting plate with 4x M5 bolts

    • Attach mounting plate to the tube with an M8 bolt/nut/washers

    • Assemble all the wiring inside the box (I've used cable lugs + additional solder on top for the power wires)

    • Configure VESC motor, ADC throttle, reverse button etc. It's a separate topic I guess.

Tagi