Liczymy pasujące modele…
Many parts of the outboard RC boat motor are designed for PLA (PLA+ or Tough PLA is recommended) filament. A few parts are designed for heat-resistant filaments (Petg, ABS, ASA). Assembly steps and details are shown in the video. Slicer…
This is a 3D printed Case for the OpenDTU Breakoutboard by blinkyparts.com: https://shop.blinkyparts.com/en/OpenDTU-Breakoutboard-Your-evaluation-for-your-balcony-solar-system/blink237542 The OpenDTU breakout board can be used to read out…
Many parts of the RC boat are designed for PLA (PLA+ or Tough PLA is recommended) filament. A few parts are designed for heat-resistant filaments (Petg, ABS, ASA). Assembly steps and details are shown in the video. Slicer settings are in…
RC Motor for small boats, suitable for 2948 electric motors, with water jacket. Bevel gear 0.5 M 12 T 3 mm 90 degrees Brass or Steel, 7mm diameter 7mm length. Small bearings 603, 3*9*3mm. Originally designed to pair with F1 Tunnel:…
Outboard Motor for Big Chill Pontoon Boat. Big Chill pontoon boat found here - https://www.printables.com/model/797773-big-chill-rc-pontoon-boat-by-black-crow Note #1 The standard parts for Big Chill are Numbered 01-05. The parts without…
Build video https://youtu.be/SllnjgBfWdE?feature=shared https://youtu.be/PSYab_l4kDQ?feature=shared ####Mercury Racing 360 Outboard Engine### Outboard file link https://cults3d.com/:2254330 -This outboard has a height of 20cm -Suitable…
El diseño del motor fuera de borda de Ethan era perfecto para usar en mi tesis universitaria, por esa razon me di a la tarea de aumentar el tamaño y adaptarlo a mis necesitades. En realidad mi bote cuenta con dos de estos motores, lo que…
Drill Powered Outboard (Work in Progress) https://youtu.be/Ix5F3YQOyLg Assembly requirements: Print 1x Propeller of your choice There is an edgeless propeller (prefix WIP), but it is an untested work in progress and requires two M10 nuts…
Do you own a Yamaha outboard motor, and need to change the fuel filter on the engine? Well, instead of buying a $25+ metal wrench that requires another wrench to work, try this! Plus side, it floats if you drop it. I own a 2015 Yamaha…
General This Spare Outboard Kill Switch Key was designed for Honda BF4, BF5 or BF6 outboards. It will probably fit other outboards as well. Printing Printed with 0.15 mm layer height, using a brim for better bed adhesion. Scaling Change…
STATIC OUTBOARD MOTOR This static outboard motor model is the perfect addition to your boat and ship models, giving them an extra touch of realism and character. ⚓🔧 Designed specifically as a display model , it is not intended to be…
3mm layer height Print upright Brim 3 walls/perimeters
This Spare Outboard Kill Switch Key was designed for Tohatsu / Mercury / Mariner / Nissan 2.5/3.5 hp four stroke outboard engines. It will probably fit other outboard engines as well. Printing I printed with 0.15 mm layer height, using a…
RC outboard motor cowling, compatible with TFL small outboard body. Inspired on the Mercury SST 120 motor. Two cowling sizes, supporting motors 2840 to 2850, and respective wires. If you looking for something a bit bigger, please see my…
Quick design of safety/start-stop key for outboard engines. Used on Yamaha outboard engine, fits and works perfectly. Printed on Creality CR-10. Model designed 5 years ago, hopefully it will be helpful to others as it was to me.
I printed this model but I always wanted to change the way the motor and cowling worked. Just personal preference . There is a body file for SLA that has the holes for brass inserts slightly bigger so they press in with a tiny bit of…
A simple oil spout to drain the oil from a Suzuki 250HP outboard engine. The original was made from rubber, but it seemed like it was for a slightly different model.
TFL Outboard Large Motor Cowling, Fits a 4074 motor and water jacket. Print in PLA, PETG or ASA. I recommend the printing positions in the image attached. Please LIKE my model when you download it and share your builds if you can. Any…
I've got an amazing replacement for the Torqeedo propeller that's a bit pricey. It's about 29cm in diameter and this version has a spline on the shaft (10 wedges) and a hole for an M10 screw. I came up with this idea after the original…
This is a temporary replacement Lever Throttle for an outboard motor. (Mercury Part# 44425) Apparently this is a common part to break resulting in no throttle from your outboard. I made this as a temporary fix to get me back on the water…
Created this plug and cap for installing a quick disconnect I bought from Amazon here: https://www.amazon.com/dp/B0C5ZBZCYK?psc=1&ref=ppx_yo2ov_dt_b_product_details . to connect to my Mercury 200HP outboard motor on my boat. This comes…
This is a case that allows you to keep both the LCD control panel and a Raspberry Pi 4b+ outside of a printer enclosure. The Rpi is mounted using two m2 screws that self tap into the two forward holes, and a pi-fan slots into the side of…
Non Commercial Use ! (See License) Hi ! Because i lost mine and i'm far away from any shipschandler. A simple Mercury Mariner gazoline caps You must use Ninjaflex or Filatech Filaflex40 (i use the last one) 0.20mm infill must be high for…
The original model was excellent - I loved it. But I'm ADHD on design nits so I created a router template for the oil channel and then applied it to the oil channel. No more block of plastic at the edge. Not that it wasn't a wonderful…
This is a lathe spindle spider to hold long pieces of work on the outboard end of the spindle. Threads onto a 34mm x 1.5 spindle. You will need (4) 8mm x 1.25 bolts and nuts. The spindle spider is threaded for the 34mm x 1.5 but only has…
Print in ABS or something else strong and heat resistant. Be careful not to crossthread. Use a new gasket if possible.
Exterior transom protection for outboard motor. It measures about 27cm in the widest part and about 19cm in the narrowest part. The height is 17.5cm. 1cm thickness. Category: Sport & Outdoors
I was looking for a nice bracket for my Chinese import PSU pcb. Couldn't find one, so made my own. You can screw the bracket from the inside on a table or something more heavy. I bought the board on Aliexpress:…
I'm restoring (some would say resto-modding) an older Delta wood lathe. Since I rarely use the outboard shaft, I decided that a handwheel of some sort might come in handy. The outboard thread on my lathe is 1" - 8 UNC left hand. I printed…
This is a very basic wedge design with a 6.5mm gap to allow you to get under the knob and push the wedge forward to move the knob cap upward so it can be pulled off more easily for those who are not strong enough to manually pull the cap…
Replacement Prop nut for a 1960 Evinrude Lark II 40hp outboard. This will likely fit similar outboards from around the same time frame. My local marina was out of stock and BRP (the manufacturer) suffered a cyber attack recently and…
Remix of the RHIB boat to add an outboard motor.
Long: Not for high pressure. 14mm thread. Should fit without any resizing, as the thread in the fitting as slightly larger. Added nut to close the other end (cone) - fits the cylinder side.
1956 Johnson Javelin 30hp Outboard Front Cover
Honda Outboard Motor (marine/boating) - oil drain plug “funnel” attaches to the drain plug - grips positively but still easy to remove. Fits Honda 20 and 15, possibly other outboards. How to use - on some of the outboards, the rubber case…
Ultra-light electric outboard motor for small watercraft (dinghies, kayaks, tiny fishing boats, etc). Features Hubless rim-driven thruster (harder to tangle or damage — can go where it's shallow, safe for marine wildlife); No need to…
The OMC connectors are different than the Honda connectors used on older outboards. I created this to us on my 1984 Honda BF75 (7.5 HP) motor, as the original cap had long been missing. TPU holds up to gasoline well, and the fit is solid…
This is a very specific part for my custom motorcycle, but who knows maybe it could be useful to someone else. This should fit a Honda CB550 fitted with a Cognito Moto 38T front sprocket that has the 3/8" offset for installing a wider…
Designed to maximize desktop space. Unlikely to fit your desk, unless desktop thickness is ~19mm. Fusion 360 file provided so you can customize to your needs. p.s. I did not bother to constrain properly, so be careful when changing Fusion…
clamp/copeling for Mariner 30hp shift shaft boat motor outboard.
Slight adjustment of scale may be neccessary depending on the shrinking properties of the particular filament you are using. It should be a very tight fit and inserts with a rubber hammer.
My Yamaha Outboard F60 had the locking trim mechanism bush heavily worn so I made this ones. They fit perfectly. Category: Sport & Outdoors
A driveshaft key that fits 1980s and 90s Johnson outboard motor water pump impeller. Probably not a permanent replacement but currently working good enough to get me out of a tight spot until my metal replacement part arrives. I printed…
Scaled down and modified mounting from the process. Added vent on top and sides. Boat available at https://makerworld.com/en/@joeytvr
Created to replace an older Honda BF75L outboard motor. 7.5 horsepower engine with a Keihin carburetor. Used TPU and it has withstood gasoline. No more leaks and the search for an “affordable” gasket is over. Feel free to adjust the size,…
This is a simple thread protector for a lathe spindle. Fits a 34mm 1.5 threads. Printer: MK3s, Filament: Inland PETG Red.
This is a remix of imp67's breakoutboard, i added a bltouch mount
Works to remove and install the retaining nut on Mercury outboards lower unit. Use a large crescent wrench to turn the tool. Replaces part number 91-91947 wrench. Works for retaining nut 11-87763. Tested specifically on a 1996 40hp Merc.…
A friend down the street broke a part off of the outboard motor on his fishing boat. I would call the deadman's switch assembly. He referred to it as the lanyard clip. Whatever the actual name is, he couldn't find a replacement part. 3D…
11/8/24 - v2 Update Increased the size of the ball & socket on the hinge for a stronger more reliable hinge Modified the design of the snap fit latch to be more secure Fixed a few issues in the Fusion360 sketch where I wasn't properly…
Made with 95A TPU. Print notes: .16mm layer height no infill 2 walls to keep it flexible, top and bottom layer at .6
Durch die Verwendung von flexiblem TPU bietet der Griff exzellenten Halt, auch bei Nässe, und ist extrem langlebig gegen UV-Strahlung und Wasser. Material: TPU (für gute Balance aus Flexibilität und Stabilität). Infill: 20 (Gyroid für…
If you bought some of these wind-up bath toys from the bargain bin: Amazon.com : Miracland Wind-up Speed Boat - Fun Bathtub Toy & Pool Toy, Windup Fast Yacht, Clockwork Speedboat for Kids (Speed Boat) : Toys & Games And found, like I did,…
Travel Spacer Blocks - Seastar Outboard Steering Struts I preinted in petg, works well enough. TPU would be ideal.
Same as my previous remix but with the addition of a 1.28" round gauge mount. Now you can design gauges anywhere!
Mercury XR6 Poppet Valve top and bottom gaskets. Printed out in TPU and been working perfectly for over a year now. When installing, be sure to watch the gasket and make sure that it doesn't get pushed out on the thinner areas.
A collection of models to mount Flipsky 85135 motor & Flipsky 75350 ESC on the standard boat transom. It has cooling channels for the water to flow along the motor. The motor casing on the photos is a bit older and cruder in comparison to…
Cowl alignment pieces for a Mercury XR6 150 outboard. Mine were damaged and one of them was missing so I created these and printed them in TPU. Its a nice snug fit but you can add some sort of glue/epoxy to make sure they dont come off…
This is water intake for outboard motor the pipe goes direcly in tube and you stick water intake on anti-ventilation plate. Its simple design but best efect. Plese suport me .
Compatible stuff... PVC pipe for turning shaft, I think like 1.25 in or 1.5 in diameter, cant remember. 36mm wide motor. standard sized servo.
The mount and tach are secured with zip ties, and the motor used is a 30hp tiller model. A link is provided for the tach that was incorporated into the design.…
Completely untested, My printer needs to be fixed but I thought should have a placeholder for this model . . . If I saved you time and effort and you feel inclined to throw me a couple bucks for the I spent modeling and actively testing…
Yamaha 2-Stroke Outboard Remote Control Cable End Replacement end fitting for the remote control cable on Yamaha 2-stroke outboard engines. This part is designed to fit certain Yamaha 2-stroke outboard models, potentially including the…
A replacement kill switch key designed for the emergency stop switch on a Honda outboard remote control. The key connects to a coiled or bungee safety lanyard worn by the operator. The other end fits into the kill switch. If the operator…
Custom wrench designed to easily unscrew and tighten the flush port plug on Mercury outboard motors. Makes routine engine flushing quick and hassle-free without damaging the plastic cap. Dimensions: Designed for square flush port plugs…
Made with 95A TPU. Print notes: .16mm layer height no infill 2 walls to keep it flexible, top and bottom layer at .6
Same as my previous remix but with the addition of a 1.28" round gauge mount. Now you can design gauges anywhere!
Durch die Verwendung von flexiblem TPU bietet der Griff exzellenten Halt, auch bei Nässe, und ist extrem langlebig gegen UV-Strahlung und Wasser. Material: TPU (für gute Balance aus Flexibilität und Stabilität). Infill: 20 (Gyroid für…
I'm restoring (some would say resto-modding) an older Delta wood lathe. Since I rarely use the outboard shaft, I decided that a handwheel of some sort might come in handy. The outboard thread on my lathe is 1" - 8 UNC left hand. I printed…
Slight adjustment of scale may be neccessary depending on the shrinking properties of the particular filament you are using. It should be a very tight fit and inserts with a rubber hammer.
A screwless case for a common 38-PIN breakoutboard.
The latch was broken when I bought this engine, a previous owner had added some kind of replacement latch on the side but it wasn't great and a new one is upwards of £80, so I decided to design a new 3D printed one. I made it a two part…
This is my 3D Printed RC Outboard Motor. I looked at the RC outboards available for purchase commercially and I was not impressed. So I set out to design my own outboard that was capable of handling high power brushless motors. This…
