1 / 2
2-Inch Y6 Coaxial Hexacopter Frame (6x 1103 Motors) — zdjęcie 1
1 / 2

2-Inch Y6 Coaxial Hexacopter Frame (6x 1103 Motors)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

"2" micro drone frame, 6 motors, Y6 coaxial config. Handles wind better. Free frame + BOM

Ocena
0 / 5
Polubienia
8
Pobrania
14
Wydruki
0
Wyświetlenia
153
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

A 2-inch micro drone frame with six motors crammed into it, because... why not?

Why this exists

I flew a Mobula 8 into the ground more times than I'd like to admit — loved the low profile, loved how quiet it was, hated how it turned into a leaf the moment there was any wind. So the question became: what if you just... added more motors? Three arms, two counter-rotating 1103s per arm, same footprint. A Y6 coaxial hexacopter, whoop-scale.

This isn't a "problem solved" frame. It's an engineering investigation, and the honest answer is mixed: it genuinely handles wind better than a standard 2-inch whoop. It's also heavier, currently flies without prop guards, and isn't a drop-in replacement for your daily basher. Full build log, CFD analysis, and flight testing are on YouTube — 侠's world — if you want the whole story instead of just the frame.

The frame shared here is already an improved version that fits 2-inch props on the top and on the bottom. 

Key Features

  • Y6 coaxial layout in an 85 mm whoop footprint: Six 1103 8000KV motors, three arms, counter-rotating pairs — more thrust authority without growing the frame.

  • Vista-reinforced structure: A symmetric TPU sandwich locks directly onto the DJI Vista's stack screws, using the Vista's own aluminum frame as a structural spine instead of fighting against it.

  • Bambu AMS ready: Printed in 68D TPU for AMS.

  • AIO-first design: Built around six-output AIO stacks — tested and flown on the Flywoo GOKU Hex 13A.

  • 159g AUW — not light for the class, and that's the whole point of the investigation.

Bill of Materials

Technical drawing

Assembly instruction

Print Settings

Orientation suggestion:

  • Material: 68D TPU for AMS — structural frame parts. Don't substitute a softer shore hardness; the sandwich design relies on this stiffness to keep six motors from turning the frame into a tuning fork.

  • Nozzle: 0.4mm

  • Wall count: 3 layers

  • Infill: 20% gyroid

  • Layer height: 0.16mm — solid top/bottom layers through the motor mounts

  • Supports: Yes

  • Print orientation: see picture

Props

2" props. Use T-mount (M2 screw) props if you can; friction-fit props on 1103s worked loose with these motors and I lost four of them in a light crash (or probably just before the crash) before switching. 

Electronics

Six T-Hobby 1103 8000KV motors, Flywoo GOKU Hex 13A AIO, Betaflight 4.5 with the native Y6 mixer. If you're chasing loop times on six bidirectional DShot streams, drop your PID loop denom before you assume your F411 is broken — full explanation in the video.

Why coaxial, not just six motors spread out?

Because the goal was "more thrust authority in the same footprint," not "bigger drone." Coaxial pairs let each arm do double duty — the lower prop rides in the upper prop's downwash and recovers some of that swirl energy, so its extra thrust doesn't cost as much power as you'd expect from a naive doubling. It's not free thrust, and I'm not going to pretend the CFD numbers on this are bulletproof at these Reynolds numbers — that's a whole separate rabbit hole.

Tagi