Liczymy pasujące modele…
A compact honeycomb storage box designed for 45mm tri-blade propellers , ideal for tinywhoops like the HappyModel Mobula 7 . Stores 3 stacks of props. The small version stores 9 props while the large stores 27 props. . Honeycomb design…
In tinywhoop racing, every last hundredth of a gram counts. But you can't have your camera break in a crash either. You need to find the right balance between durability and weight. That's what the Joker is for. Material: TPU95A. For me,…
Frame for a 31mm "Tinywhoop" style drone with a 25mm AIO board (the board in the examples is the EMAX Nanohawk AIO). The major issue with this design is flexion of the "X" base affecting trim. Print it with as stiff a material as possible…
This is just the Battery insert for the BetaFPV Air65 Tinywhoop Case made by melnikod !!! I shrinked just the general size (red markings) by 0.2mm, because it would not fit. The Battery recesses are now a little wider by 0.2mm (red…
Landing pad for your tinywhoops. Supportless print. Legs latch in open/closed positions. Can be printed in 3 segments to fit on the Prusa MK4. You'll then need 6 M3 screws and nuts to join the parts. The cool mesh grid can be achieved by…
Optimized fir Meteor75 Pro, 1.5g only. Printet with tpu95a. No supports needed. https://tressym.eu/parts/joker - original designers, check them out!
This 3D-printable battery case is designed for TinyWhoop drones and holds up to 4 GEPRC 1S batteries (530mAh / 380mAh) . The case features two separate sections , each holding 2 batteries and secured with a double-sided lid . Each lid has…
I wanted to have a neat way to display and store my drones on my shelf, but i wanted it to be modular and easy to print. I tried to find something fitting online, but couldn't find anything that really met my expectations, so i hopped…
The inspiration was the Jron2008's WhoopDegen case ( https://www.thingiverse.com/thing:6572641 ), but it was too big for my taste. But then I found the CH26's design ( https://www.thingiverse.com/thing:6734248 ), but it was for 75mm, so I…
the connectors can best be printed laying down for additional strength using a bit of support. You need 4 feet and one body and connector. I made some holes to add electronics and maybe leds when I get to it. The corrugated pipe connector…
I needed a quick and simple way to connect lengths of PVC pipe together without buying expensive connectors. In my case DIN EN 61386-21 with an outer diameter of 20mm Printtips The files print without support and should be correctly…
Instructions for printing: for bambu studio or other Slic3r slicer just open the 3mf file to change your printer and fillament settings for other slicers the scale factor for the og parts is 90.16% I used 15% infill with 2 wall loops…
Tinywhoop Balls - The Ballsiest Tinywhoop Accessory Feeling unsure about diving that building? Don’t worry, I’ve got you covered. Add some confidence to your micro quad with some Tinywhoop Balls ! They serve absolutely no real purpose…
Features Fully customisable to suit any diameter of PVC pipe and to suit your own printer tolerances. Accurately calculates the length you need to cut your PVC pipe to in order to achieve a specific dimension (see OpenSCAD console…
A case for 5 pcs tinywhoop 1s lipo batteries. I designed it specifically for the BetaFPV LAVA 1S 300mAh 75C Battery, but other similar batteries may also fit in. https://betafpv.com/products/lava-1s-300mah-75c-battery-5pcs I printed this…
Model to build tinywhoop race gate made from "Pipe Insulation Foam Tube". Final gate size is 35cm height and 40cm width. I parametrized few dimensions to better fit different pipe sizes. Pipe dimensions used by me: - inside pipe holde…
Designed for the mobula 7. A quick ~10 minute print to make your tinywhoop drone more stylish. Print with 5 or more edge loops at 0 distance from the model. 15% infill, no supports, PLA. License -…
Monitor model: [SoloGood 800*480 5.8G FPV Monitor with DVR 40CH 4.3 Inch LCD Display 16:9 NTSC/PAL Auto Search Video…
Simple upgrade to larger props for the US65 drone, should fit other FC's too though. Spans 87mm, and fits 52mm props. Tried to implement little motor guards :) Hardware: 4 x m2x12 Rubber bands for holding the battery I used this canopy by…
A remix of the original design by Crytorius to hold whoops with 2S 12.5x14mm LiPos. This is just the stand. You will also need the base from Crytorius' original project .
BetaFPV Air65 Tinywhoop LED bar Upgrade for BetaFPV Air racing whoop for 3 WS2811 LED strip compatible with original BetaFPV canopy. VTX antenna mount no glue hole for wiring fast repair and replacement Use BFlex or TPU filament. 2…
Someone in the comments mentioned that original canopy is too thin for TPU so I added 0.5mm thickness for it
adjustable clamp to hold ½ in PVC pipe for the purpose of making collapsible, adjustable, lightweight gates to fly through uses 1 M4x20 bolt for each clamp and 1 M4x8 bolt+nut to connect two together Category: R/C Vehicles
You can make the form yourself, if you want a square of maybe a pole! everything is possible!!!🙃
So I needed a way to carry my tinywhoop, and I really liked the U.S. General gridfinity setup that Uncle Jessy showed off. This is just one of the bins that I made for my system. I needed a pin to go through the center of the props to…
🛫 TinyWhoop Launch Pad with LED & 80mm Fan Also doubles as a soldering station with LED lighting and smoke extraction Also doubles as a soldering station with LED lighting and smoke extraction Designed for 65–75mm Tiny Whoop drones, this…
This is a lightweight TPU mount (0.76g) designed for the Foxeer M10Q-120 , one of the lightest GPS + compass modules (2.7g). It fits directly into the rear screw holes of TinyWhoop-style frames and can be secured with glue if needed.…
If you want print frame give feedback please so that i could change. (I'm just learning) https://t.me/Lov3cp
Tinywhoop 75mm frame size, canopy dedicated for 14mmx14mm camera with Ф4mm hole antenna holder.
it fits 22 standard gens ace, tattu, lava 300mah batteries (should also fit 260mah). Vertical/horizontal holes for marking charged/discharged batteries (cahrged vertically |, discharged horizontally - because it represents a minus.. :D)…
a bunch of parts and connectors that will let you convert pool noodles into a tinywhoop flying course printed fully in PLA, used supports only on the base plates, but what you use might depend on your printer. no sanding or gluing…
A compact honeycomb storage box designed for 45mm tri-blade propellers , ideal for tinywhoops like the HappyModel Mobula 7 . Stores 3 stacks of props. The small version stores 9 props while the large stores 27 props. . Honeycomb design…
System of FPV gates for indoor flying. With this system you should be able to make indoor-scale version of FPV gates including a flag pole, ladder, dive gate and more. Should make a scale model of a full 5" racing track in your home.…
In tinywhoop racing, every last hundredth of a gram counts. But you can't have your camera break in a crash either. You need to find the right balance between durability and weight. That's what the Joker is for. Material: TPU95A. For me,…
Mantis repo "Mantis" is 1,2" printable freestyle/racing 1S tinywhoop watch out! I'm updating this project often here, for best and actual files please visit my repo. There you can find most actual description and files:…
Tinywhoop canopy with standard 25.5mm mounting holes. Fits nano sized cameras (14mm wide) such as Caddx Baby Ratel, Runcam Nano 4 etc. Fusion360 project included. Weight is about 1.7 g (polycarbonate, 1.1x extrusion multiplier). Not the…
Compact and durable FPV racing gates designed for TinyWhoop-class micro drones . This model is made to fit 20 mm tubes — perfect for building lightweight and portable indoor race tracks. Print Settings: Material: PETG Layer height: 0.2 mm…
A super simple desk stand for your tinywhoop Print in PLA No support 12% infill is way enough 0.4mm Nozzle It prints pretty quick and can hold the weight of your tinywhoop without using too much filament.
A simple system to grab batteries when flying...and not trying to remember if you put the empty one in the 'good pile'! The battery sorters can fit 8 X lava 1s 550ma batteries. There are a few models available: Low and full battery…
fiz esse modelo para facilitar colocar essas pulseiras por lugares. Se só um não segurar recomendo colocar dois.
Just added little indicators to easily differentiate between the models
I designed this ultra-light canopy specifically for the Walksnail Ascent Lite Kit for TinyWhoops and Toothpicks . Since there are currently no other canopy options available for this kit, I decided to upload my design to fill the gap for…
Build some cheap, easy to make tiny whoop racing gates for under $6 each form ½ in PEX tubing, a couple of 3D printed parts, and so fairy lights from Dollar Tree I wanted some low cost, easy to build LED whoop gates. I tried a couple of…
Frame for a 31mm "Tinywhoop" style drone with a 25mm AIO board (the board in the examples is the EMAX Nanohawk AIO). The major issue with this design is flexion of the "X" base affecting trim. Print it with as stiff a material as possible…
This is just the Battery insert for the BetaFPV Air65 Tinywhoop Case made by melnikod !!! I shrinked just the general size (red markings) by 0.2mm, because it would not fit. The Battery recesses are now a little wider by 0.2mm (red…
the worst nightmare for a tiny whoop: A FEILD OF LONG GRASS. This is a joke model that tiny whoop enthusiasts can put on their desk. I recommend you to print it with supports but the cool thing is that you dont even have to remove them…
I really like what RockStarAlchemist did with the case, but wanted one that would accommodate the mullet mod (which removes one battery section) and would also be less tall (because it didnt need AS much height). notice…
Landing pad for your tinywhoops. Supportless print. Legs latch in open/closed positions. Can be printed in 3 segments to fit on the Prusa MK4. You'll then need 6 M3 screws and nuts to join the parts. The cool mesh grid can be achieved by…
Optimized fir Meteor75 Pro, 1.5g only. Printet with tpu95a. No supports needed. https://tressym.eu/parts/joker - original designers, check them out!
This 3D-printable battery case is designed for TinyWhoop drones and holds up to 4 GEPRC 1S batteries (530mAh / 380mAh) . The case features two separate sections , each holding 2 batteries and secured with a double-sided lid . Each lid has…
Create drone race gates for your tinywhoop using 19 mm pvc pipe for electrics. All possible corner pieces to build drone race gates for your small drone. Ideal for in the backyard, the hinges will allow you to partially fold up the gates…
super light stand designed for the betafpv air65 but may work with other tiny whoops. can be a be a bit tricky to set up as you will have to put the stand into the battery slot on the drone before setting it down. Print sideways with no…
I love this drone (especially without the propeller guards) :) Please enjoy the STL, SVG and STEP files for the EMAX Nanohawk drone's frame . I also made a version that supports standard tinywhoop motors (like 0802s).
40mm duct not unlike the ones seen on jacks3dprinting hope they work well for you! let me know if you need them adjusted
I liked the original design a lot, but I prefered to have a case where I can put all my things in... So I created that remix. It will have enough space to fit a small BetaFPV Lipo Checker... of course you can use it for sth. else too,…
I wanted to design a frame for the Eachine E010 style drones that is very light but can withstand crashes. So here it is in 6mm and 7mm motor variations. I play a lot with my E010 built into this frame and I crash a lot but the frame…
This is a mount for the eachine tx02 camera ( https://goo.gl/4is3j3 ), to mount it on a common tinywhoop-frame. One part is without a tilt, the other one has a 10 degree tilted cam-holder. I also added the Sketchup-files, so that you can…
a canopy canopy for the Ant Lite designed to hold the cam at different angles (15°-45°). Multiple versions
A tiny whoop battery organizer for the Gridfinity system. Fits 8 NewBeeDrone NitroNectar Gold 1S 300mAh batteries and 8 EMAX 450mAh 1S batteries.
Camera Mount for Tinywhoop Racing 15 - 55 degree tilt McStinkyHDZ is for the HDzero Nano Lite, there are also spacer files to raise the mounting point above the vtx board. TheMcStinky is for cameras with a 10mm lens and 12mm body, like…
I have previously made a 22.9g walksnail whoop, using the under-frame mounting of the FC style popularized by Shutterbug FPV (See my other models). This time i wanted to use the new Meteor65 Air frame, but unfortunately there is not…
Print both halves in their normal orientation, the latches print on their side. You'll need 6 x M3 bolts with 16mm thread length.
My first attempt of creating 3d model. Printed with PLA on K1, feels pretty solid
A slick little 1S battery box for tinywhoop batts. The four inserts are removable and slots snugly into a designated place in the box. Print the seal in TPU. (Seal optional. Box works just fine without it.) Print the inserts in whatever…
Sized correctly for a 65mm tiny whoop, a little room for batteries
This is a 75mm whoop frame I designed to replace me broken mobula 7 frame. Honestly, I have never tried it because I had a spare non-printed frame, so I would enjoy some feedback if it works well. Category: R/C Vehicles
This is a strong and light Tinywhoop style (25.5 x 25.5 mounting) canopy specifically deigned for Runcam Nano 3 Here is available two models: - 52mm with 52mm home for antenna. Originally antenna have 5mm diameter, so this model will fit…
This canopy is based on the work done by Slavik Nychkalo (https://www.printables.com/model/812479-tinywhoop-canopy-runcam-nano-3/related). I was looking for a new light canopy for a project and I liked his model, but his model was for a…
Those boxes will carry your tiny (or larger) batteries with style! No hardware required – simply insert a piece of filament in the hinge holes . Print with 0.2mm layers, 0.45 line width (or Arachne wall generator). I printed mine out of…
Small cover for exposed flight controller board on tinywhoops with 25.5mm mounting Part is showcased in video above.
This is a storage and travel case for a Mobula6 tiny whoop, but any 65mm tiny whoop should fit. Pictured is the case holding a 2024 Happymodel Mobula6 HDZero ECO. I designed the case to fit the original foam that the quadcopter was…
Lightweight canopy for tinywhoops that holds camera (Caddx Ant) and vtx (HGLRC Zeus Nano).
In case somebody needs a 3d model of mob7 frame for making custom canopy or whatever. The model is accurate to the production frame except symmetrical motor arms and straight duct profile.
It requires 4 M1.4x14 screws to mount the stack on the mob7 frame, 2 M1.4x6 to clamp the top bracket and 2 M1.2x4 screws to fix the camera on both sides.
I wanted to have a neat way to display and store my drones on my shelf, but i wanted it to be modular and easy to print. I tried to find something fitting online, but couldn't find anything that really met my expectations, so i hopped…
Basic stand for Tinywhoops. Has some steep overhangs, so be sure your printer can handle angles of approximately 55 degrees from verticle axis (ie, high fan and slower printing). My version is not a great example as the overhangs are…
Tinywhoop wall mount for 65mm or 75mm (maybe 85mm too). Since tinywhoops are so light, this can be mounted on the wall with just BluTack. Of course you can use 3M or other double sided tape as well for a more secure mounting. Print in any…
I wanted to make a parameterizable pack holder that would work for all my different small fpv batteries and I'm pretty happy with how this came out! I'd recommend measuring your pack then adding a small amount of padding to taste. Between…
This is a canopy for the BetaFPV Air Tinywhoops, like the Air65 and Air75. The longer tail section allows a lower camera angle to be set. I also made a widening in the area of the right holder to additionally fix the antenna connector. I…
