1 / 12
Vixen Phone Holder, 200 mm Offset Arm & Holder Rod | Parametric Fusion — zdjęcie 1
1 / 12

Vixen Phone Holder, 200 mm Offset Arm & Holder Rod | Parametric Fusion

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Pixel 7a cradle for Vixen saddles, optional 200 mm offset arm, and Sun-shadow north reference rod for Polar Mount Align.

Ocena
0 / 5
Polubienia
1
Pobrania
24
Wydruki
0
Wyświetlenia
192
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
GNU General Public License v2.0

A smartphone holder for the Vixen saddle on an equatorial telescope mount, intended for phone-assisted polar alignment of the mount itself. Use the original direct mounting position, or add the optional 200 mm lateral offset arm to move the phone farther from the mount. The same dovetail and phone cradle are used in both positions.

The direct setup uses two printed parts, two M4 screws and two brass heat-set inserts. The offset setup adds one printed arm, two more M4 screws and two more brass inserts. The phone keeps the same nominal orientation; the arm translates it sideways and raises it by 18 mm without tilting it.

The included STL files are sized for a Google Pixel 7a without a case. The parametric Autodesk Fusion project is included in F3D format, so you can change the holder dimensions to fit your phone and export your own version.

The optional holder rod adds a physical shadow reference for true north directly in the free Polar Mount Align Android app.

Features

  • Separate Vixen dovetail, phone cradle and optional offset arm, printed individually.

  • Two M4 mounting points spaced 40 mm apart at each connection, with the cradle screw heads recessed below the phone support surface.

  • Two integrated locating keys to keep the parts aligned.

  • A through-opening in the back plate to leave the camera bar clear.

  • An upper snap-fit clip, lower retaining lips and a central opening for the USB connector.

  • Designed for PETG with a 0.4 mm nozzle and 0.3 mm layers, without supports in the specified orientation.

Two mounting positions

  • Direct: fit the phone cradle directly onto the Vixen dovetail, using the original locating keys and two M4 screws.

  • Offset: fit the arm onto the same dovetail interface, then fit the unchanged cradle onto the locating keys at the other end of the arm.

The supplied arm has 200 mm between mounting centres. Its complete printed dimensions are 232 × 80 × 20 mm: an 18 mm beam plus 2 mm locating keys. The open channel has a 6 mm bottom web and two 12 mm side ribs. The printed arm is fixed-length; changing its offset requires editing the Fusion parameter and printing a new arm.

For the intended alignment workflow, keep the phone's bottom-to-top direction parallel to the mount's polar axis, with RA and DEC in their repeatable mechanical zero positions. The phone measures orientation, so a lateral translation does not require an angular correction in the ideal rigid geometry. Confirm the mounting reference and calibration again after changing between the direct and offset setups.

Moving the phone away from the mount may reduce magnetic disturbance, but 200 mm is not a guaranteed interference-free distance. Nearby screws and other hardware can still affect the compass. Compare readings in both positions using a verified direction reference; a stable compass reading alone does not prove accuracy. The real arm's stiffness, joint play and repeatability must also be checked with the phone fitted.

Adjusting the holder for another phone in Fusion

  1. Open Supporto_telefono_Vixen_parametrico.f3d for the direct setup, or Vixen_Phone_Holder_Offset_parametric.f3d for the offset setup. The latter contains all three components and lets you customise both the phone cradle and the arm. Save a copy for your configuration.

  2. Open Modify → Change Parameters.

  3. Set telefono_larghezza (phone width), telefono_altezza (phone height) and telefono_spessore (phone body thickness) to your phone's dimensions. If you use a case, measure the phone with the case fitted. Exclude the camera bump from the body thickness.

  4. Adjust camera_da_sopra and camera_zona so the opening clears the entire camera bump, with some space around it.

  5. Check the positions of the buttons, connectors and retaining lips. Adjust bordo_laterale_lunghezza and other cradle parameters if needed.

  6. Recompute the model and check for timeline errors. Export the changed phone cradle as an STL in millimetres. Export the arm too if you changed its parameters. Select each individual component rather than exporting the assembled parts as one STL. Check the updated geometry in your slicer's preview.

Use the Fusion parameters to adapt the holder. Scaling an STL would also change the M4 holes, insert pockets and Vixen fit. Keep the formulas in the derived parameters linked to the main dimensions. Parameter names in this description match the existing Fusion project and retain their original Italian identifiers; their meanings are explained below.

Main parameters in the included version

Fusion parameter

Value

Purpose

telefono_larghezza

72.9 mm

Pixel 7a width without a case

telefono_altezza

152 mm

Phone height

telefono_spessore

9 mm

Phone body thickness, excluding the camera bump

gioco_telefono

0.3 mm per side

Initial clearance; adjust to suit your print

camera_da_sopra

8 mm

Distance from the phone's top edge to the start of the camera opening

camera_zona

34 mm

Height of the camera opening

bordo_laterale_lunghezza

48 mm

Length of the lower side guides

interasse_fissaggio

40 mm

Centre-to-centre distance between the two M4 screws

vixen_larghezza

43.8 mm

Maximum dovetail width

inserto_foro

5.6 mm

Insert pilot-hole diameter; adjust to your actual inserts

The included camera opening measures 73.5 × 34 mm. Its position is a design assumption that must be checked against the actual phone: the phone's back should rest on the support surface while the entire camera bar remains clear of the material. Camera and button positions are not determined automatically from the phone's overall dimensions. Compatibility with other cases and saddles depends on their dimensions.

Changing the arm dimensions in Fusion

  1. Open Vixen_Phone_Holder_Offset_parametric.f3d and save a copy.

  2. Open Modify → Change Parameters.

  3. Change barra_decentramento to the required centre-to-centre offset in millimetres. For example, enter 150 mm for a shorter arm. The arm geometry and the cradle's assembly position update together, keeping the same orientation.

  4. For a distance-only change, leave the other arm parameters, locating keys, M4 spacing and insert dimensions unchanged.

  5. Recompute and inspect the model. Export component 03_Barra_laterale_parametrica alone as an STL in millimetres. Place its flat underside on the build plate, with the open channel and locating keys facing upwards.

Fusion parameter

Included value

Purpose

barra_decentramento

200 mm

Lateral distance between mounting centres; overall arm length is this value plus the mounting-pad length

barra_altezza

18 mm

Beam height and cradle lift, excluding the 2 mm locating keys

barra_fondo

6 mm

Continuous bottom-web thickness

barra_nervatura

12 mm

Width of each longitudinal side rib

barra_larghezza

80 mm

Overall width; derived from collo_lunghezza

barra_testata

32 mm

Length of each end mounting pad; derived from collo_larghezza + 4 mm

barra_raggio

3 mm

Vertical outside and channel corner radius

barra_sotto_testa

2.7 mm

Material below the base screw heads; matches the original cradle's screw grip

Regeneration, orientation, interference and mesh checks were performed at 150, 200 and 250 mm, with the other arm dimensions fixed at the values above. These are geometric tests, not a rated mechanical adjustment range. Longer or thinner arms flex more. Changes to height, ribs, bottom web or mounting pads require renewed stiffness, insert-depth and printability checks. Do not set the offset to zero to obtain the direct setup: use the original two-part assembly instead.

Printing in PETG

  • Intended material: PETG.

  • Nozzle: 0.4 mm.

  • Design layer height: 0.3 mm.

  • Supports: the geometry is designed to print without them in the orientation described below.

  • Vixen dovetail: place the wide, flat bottom face on the build plate, with the locating keys and insert pockets facing upwards.

  • Phone cradle: place the flat back on the build plate, with the clip extending upwards.

  • Offset arm: flat underside on the build plate, with the open channel and locating keys facing upwards. Allow space for its 232 × 80 mm footprint and any brim.

The retaining lips and upper release tab have underside ramps at approximately 63° to the build plate. The locating-key slots pass through the back plate, so they have no suspended ceilings. The clip is 1.6 mm thick; its root and the retaining lips are 1.8 mm thick.

In Cura, place each part on the build plate without scaling them. The dovetail STL retains its assembly coordinates, with its bottom at Z = −18 mm: use the command that drops the model onto the build plate. Use a PETG profile already calibrated for your printer and inspect the toolpaths around the clip. No G-code or universal temperature, speed or infill profile is included.

Required hardware

The quantities below are for the direct setup. For the offset setup, use four screws and four inserts in total: two pairs at the dovetail-to-arm connection and two pairs at the arm-to-cradle connection.

  • 2 M4 brass heat-set inserts, 8 mm long. The pilot holes are Ø5.6 mm and 8.5 mm deep. Adjust the diameter to your insert model and the manufacturer's recommendations.

  • 2 M4 × 10 socket head cap screws. The counterbores are Ø8 mm and 4.5 mm deep. Screw heads must be no more than 4 mm high to remain below the phone support surface.

Direct assembly

  1. Install the inserts from the top of the Vixen dovetail, flush with or slightly below the surface.

  2. Fit the two locating keys into the through-slots in the phone cradle.

  3. Insert and tighten both screws from above before fitting the phone. Check that their heads remain recessed.

  4. Slide the phone's lower edge under the retaining lips, then gently guide its upper edge past the clip.

  5. To remove the phone, gently pull the upper release tab outwards and lift the phone out.

Offset assembly

  1. Keep the original inserts installed in the Vixen dovetail. Install two additional M4 brass heat-set inserts in the blind holes at the arm's raised-key end.

  2. Fit the arm's through-slots over the dovetail's existing locating keys. The arm's flat underside rests on the dovetail's support neck.

  3. Insert two M4 × 10 screws through the deep recesses at this end. Use a hex driver that reaches the recessed heads. Tighten while keeping the locating keys seated consistently.

  4. Fit the unchanged phone cradle onto the locating keys at the other end, with its support surface facing upwards and its top edge pointing in the same direction as in the direct setup.

  5. Fasten the cradle with two M4 × 10 screws, then fit the phone. Check that all mating surfaces sit flat, screw heads remain recessed, and the assembly has no perceptible play.

  6. Confirm clearance around the mount and check repeatability with the phone installed. Let the assembly settle after touching the screen before taking alignment readings.

To return to the direct position, remove the arm and fasten the same cradle directly to the same dovetail. No replacement dovetail or cradle is needed.

Holder rod: north reference for Polar Mount Align

The holder rod is an attachment that turns the phone cradle into a shadow-based north reference for daytime polar alignment in Polar Mount Align. While the phone rests in the cradle on the mount, the rod casts its shadow across the display. The app calculates the position of the Sun and draws parallel lines indicating where the shadow falls when the mount points north; the app then holds true north for the alignment.

The two printed parts

The rod assembly clips together without fasteners and never contacts the phone glass:

  • 04_Holder_Rod_Base.stl: slides onto the bottom short end of the Pixel 7a cradle from behind. An alignment key engages the cradle's USB port cutout to centre the base automatically.

  • 05_Holder_Rod.stl: a 3 × 3 mm straight rod on a flat foot. The foot slides into the inclined slot of the base along two lateral channels. Once seated, the rod leans 40° from the perpendicular to the screen towards the top edge of the phone and extends 190 mm from the base.

Required conditions

  • Direct sunlight with the Sun at least 10° above the horizon and positioned on the screen side of the phone.

  • Equatorial mount set in its home position (saddle parallel to the polar axis), with the top edge of the phone pointing towards the celestial pole.

  • If the Sun is positioned towards the pole, the app requests lowering the polar axis to a specified angle to receive the shadow, and prompts raising it back to latitude once confirmed.

  • If conditions prevent the rod from working (the Sun is below 10°, behind the screen, the polar axis is steeper than 80°, the shadow would be too short or off the screen, the shadow turns too little, or two directions would give the same shadow), the app reports the cause and suggests using the "Sun's shadow" method instead (a separate method with the phone laid flat using an upright object such as a rod or tripod leg).

Step-by-step procedure

  1. Slide the base onto the cradle, insert the rod into the base slot, and set the mount to its home position.

  2. In the app, navigate to Tools › North reference › Holder rod and select "Show the lines".

  3. Rotate the tripod and adjust the mount azimuth screw until the shadow cast by the rod is parallel to the lines on the screen.

  4. Tap "The shadow is on the lines". The phone's gyroscope captures and holds the true north reference without moving any hardware.

  5. Tap "Save the compass correction for this mount" to save the correction for this mount, so later sessions can rely on the compass.

For additional diagrams, consult the chapter "North from the holder rod" in the user guide inside the app.

Making your own rod for other cradles

For custom or third-party phone cradles, a rod can be fabricated independently. It must be a rigid, straight rod roughly 3 mm thick and 190 mm long from its attachment point, fixed securely to the cradle (clear of the screen glass) at the centre of the bottom short edge. It must tilt 40° towards the top edge of the phone with zero lateral lean. See Holder_Rod_Guide.pdf for tolerances and the dimensioned drawing of the rod geometry.

Included files

  • 01_Coda_Vixen.stl — printable Vixen dovetail.

  • 02_Portatelefono_Pixel_7a.stl — phone cradle sized for a Pixel 7a without a case.

  • Supporto_telefono_Vixen_assieme.step — assembly for use in other CAD applications.

  • Supporto_telefono_Vixen_parametrico.f3d — original direct-mount Fusion project with its timeline and user parameters.

  • 03_Offset_Arm_200mm.stl — optional arm with a 200 mm centre-to-centre offset, ready to import into your slicer.

  • Vixen_Phone_Holder_Offset_200mm.step — three-part offset assembly.

  • Vixen_Phone_Holder_Offset_parametric.f3d — three-part Fusion assembly with editable phone and arm parameters.

  • 04_Holder_Rod_Base.stl — clip-on base for the Pixel 7a phone cradle.

  • 05_Holder_Rod.stl — 190 mm shadow rod with 40° inclined mounting foot.

  • Holder_Rod_Guide.pdf — complete user manual and dimensioned drawing of the rod geometry for custom rods.

Tagi