1 / 3
Caster v2 — ESP32-C3 Robot Car with N20 Gear Motors | minirobo — zdjęcie 1
1 / 3

Caster v2 — ESP32-C3 Robot Car with N20 Gear Motors | minirobo

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A tiny ESP32 robot with LED eyes, a voice and four moods. STLs here; firmware and the full build guide at minirobo.io

Ocena
0 / 5
Polubienia
4
Pobrania
7
Wydruki
0
Wyświetlenia
129
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
RC & Robotics
Licencja
Creative Commons — Attribution

Caster is a two-wheel desk robot about the size of your palm: 84 × 84 mm, two N20 gear motors, a swivelling rear caster, two LED eyes and a piezo voice. It has four moods (excited, sulk, startled and adore), and it plays each one as lights, a tune and a little wheel movement all at once. You drive it with an Xbox controller, from your phone, or with the minirobo handheld.

v2 is the same robot as v1 with the wire nest gone. The ESP32-C3, the DRV8833 motor driver and a 5 V boost module plug into sockets on one small carrier board, minicore, which screws up under the lid's roof. Nothing expensive is soldered to anything, so a dead part just pulls out.

All the printed parts are here. The firmware, the wiring map, the parts list with buying links and the full build guide are free on the project page: minirobo.io/projects/caster-v2

Watch it built

  • Episode 6 — the whole robot, built end to end

  • Episode 7 — turning the wiring into a real circuit board

What to print

12 pieces from 9 files.

File

Qty

Material

Notes

chassis

1

PLA

lid

1

PLA

prints roof-down

faceplate

1

PLA

looks best in a contrast colour

wheel

2

PLA

outboard face down

tire

2

TPU

caster_fork

1

PLA

support under the two cheeks, plus a brim

caster_mount

1

PLA

caster_wheel

1

PLA

piezo_clamp

1

PLA

Print settings

  • Every file is already in print pose. Slice them as they load and don't rotate anything.

  • 0.2 mm layers, 3 perimeters, 20–25% infill.

  • No supports anywhere except the caster fork, which wants light support under its two cheeks. Lying on its side it only touches the bed over about 18 mm², so give it a brim.

  • The tires print in TPU at 0.2 mm. The tread is on the vertical wall, so no support and no ironing.

  • The wheel bore is Ø3.15 in the file and prints to about 3.05 on the 3.00 mm motor shaft, which gives a firm push fit.

  • A whole robot takes about 102 g of PLA and 16 g of TPU.

Hardware you'll need

  • 2 × N20 gear motor, 3 mm D-shaft. They snap into the chassis with no screws.

  • 3 × M2 self-tapping screw for the caster. The one that holds the fork goes in snug, not tight: it bottoms out on purpose so the fork stays free to swivel.

  • 4 × M2 × 5 self-tapper for the board. Not M2 × 6, which bottoms out.

  • 2 × M2 × 6 self-tapper for the piezo clamp.

  • Ø20 piezo disc, two 5 mm LEDs (one blue, one red) and a 1S LiPo.

  • A minicore board carrying an ESP32-C3 SuperMini, a DRV8833 and a 5 V boost module.

The lid holds on with four printed pegs that drop into pockets in the deck, so there are no magnets and no lid screws. Buying links for every part, the wiring and the firmware are on the project page.

If you print one, post a make. I'd love to see what colors you pick.

Tagi