1 / 1
ALTO G DOUBLE WHISTLE - PENTATONIC MELODY + DRONE — zdjęcie 1

ALTO G DOUBLE WHISTLE - PENTATONIC MELODY + DRONE

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A 3D-printed double whistle in G: one fingered pentatonic melody pipe and one plain drone pipe.

Ocena
0 / 5
Polubienia
2
Pobrania
3
Wydruki
0
Wyświetlenia
39
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Music
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

ALTO G DOUBLE WHISTLE - PENTATONIC MELODY + DRONE

=================================================

A 3D-printed double whistle in G: one fingered pentatonic melody

pipe and one plain drone pipe, both fed from a single forked

mouthpiece so they sound together from one breath. The melody pipe

plays G A B D E in two octaves; the drone holds a steady low G

underneath.

Bottom note: G (the G above middle C, G4), on both pipes.

Bore: 20mm, cylindrical.

Assembled length: about 460mm from mouth tip to foot on each side.

License: CC BY-NC-SA 4.0

PARTS LIST (7 prints)

---------------------

File Qty Notes

-------------------------------- --- ----------------------------

AltoG_DualMouthpiece_YFork.stl 1 forked mouthpiece, both

windways in one piece

AltoG_Piece1.stl 2 plain extension, one per

side (identical)

AltoG_MelodyBody.stl 1 4 finger holes

AltoG_MelodyFoot.stl 1 plain foot, melody side

AltoG_DroneBody.stl 1 no holes

AltoG_DroneFoot.stl 1 sleeve foot, drone side

Longest part is the melody/drone body at about 241mm, so you need at

least 245mm of Z build height to print it standing up.

PRINTING

--------

- Tested in PLA.

- Print the tubes standing upright, tenon end down. They are plain

cylinders and need no supports.

- Print the drone foot with its socket (the wide end) facing UP.

The socket floor is then an upward-facing ledge and needs no

support.

- The forked mouthpiece is the only complex part. Take your time

with it and check that both windways are clean and open before

assembling. A thin strip of card or paper slid gently through each

windway will clear any stringing.

ASSEMBLY

--------

Each side is a stack of push-fit joints, starting from the fork:

MELODY SIDE: YFork -> Piece1 -> MelodyBody -> MelodyFoot

DRONE SIDE: YFork -> Piece1 -> DroneBody -> DroneFoot

Every joint is a tenon going into a socket EXCEPT the drone foot.

The drone foot is a sleeve that slides OVER the plain end of the

drone body.

Both feet matter for pitch. Each one adds the length that brings

its pipe down to G. Leave either one off and that pipe plays a whole

tone sharp (A instead of G).

Do not glue anything until you have played it. The push fits let

you tune (see below).

A NOTE ON JOINT FIT - PLEASE READ

---------------------------------

The joints were sized for the printer these were designed and

tested on. That printer prints outside diameters about 0.4-0.5mm

under size, so the tenons are drawn slightly oversize to make up

for it. Your printer will almost certainly be different.

- If a tenon is too tight: sand it lightly and evenly, turning the

part as you go, and test often. Do not force it. A jammed joint on

a 240mm tube gives you a lot of leverage to crack something.

- If a joint is loose: wrap the tenon with a turn or two of PTFE

(plumber's) tape, or thin paper tape, until it is snug.

- Airtight matters more than tight. A leaking joint makes the pipe

weak and breathy.

TUNING

------

The two pipes should agree on the bottom G. Play the melody pipe

with all holes covered together with the drone, and listen for

beating (a slow wobble in the sound):

- Pulling a joint out a millimetre or two makes that pipe LOWER.

- Pushing it fully home makes it as high as it will go.

Pulling out the Piece1 on either side is the easiest adjustment.

Once the two agree, you can mark the joint positions, or glue them

if you want the settings fixed for good.

PLAYING

-------

The drone has no holes. It just sounds while you play. Hold the

instrument with the melody pipe under your fingers.

The melody pipe has 4 holes. Cover them with the top hand on the

upper two holes and the bottom hand on the lower two. The wider gap

in the middle of the hole layout is normal: it is where a standard

whistle's missing hole would be.

Holes are numbered 1 to 4 from the mouthpiece end

(X = covered, O = open):

Note 1 2 3 4

---- ----------

G X X X X

A X X X O

B X X O O

D X O O O

E O O O O

Each step up the scale lifts one more finger, working from the

bottom. Blow harder with the same fingerings for the second octave.

Because the scale is pentatonic, every note fits over the G drone,

so there are no wrong notes to avoid.

Tagi