ALTO G DOUBLE WHISTLE - PENTATONIC MELODY + DRONE
We calculate the final price from your selected file. You review and accept it before payment.
Saved on this device.
A 3D-printed double whistle in G: one fingered pentatonic melody pipe and one plain drone pipe.
- Rating
- 0 / 5
- Likes
- 2
- Downloads
- 3
- Makes
- 0
- Views
- 41
- Reviews
- 0
Updated at source:
Model information
- Source
- Printables
- Category
- Music
- License
- Creative Commons — Attribution — Noncommercial — Share Alike
ALTO G DOUBLE WHISTLE - PENTATONIC MELODY + DRONE
=================================================
A 3D-printed double whistle in G: one fingered pentatonic melody
pipe and one plain drone pipe, both fed from a single forked
mouthpiece so they sound together from one breath. The melody pipe
plays G A B D E in two octaves; the drone holds a steady low G
underneath.
Bottom note: G (the G above middle C, G4), on both pipes.
Bore: 20mm, cylindrical.
Assembled length: about 460mm from mouth tip to foot on each side.
License: CC BY-NC-SA 4.0
PARTS LIST (7 prints)
---------------------
File Qty Notes
-------------------------------- --- ----------------------------
AltoG_DualMouthpiece_YFork.stl 1 forked mouthpiece, both
windways in one piece
AltoG_Piece1.stl 2 plain extension, one per
side (identical)
AltoG_MelodyBody.stl 1 4 finger holes
AltoG_MelodyFoot.stl 1 plain foot, melody side
AltoG_DroneBody.stl 1 no holes
AltoG_DroneFoot.stl 1 sleeve foot, drone side
Longest part is the melody/drone body at about 241mm, so you need at
least 245mm of Z build height to print it standing up.
PRINTING
--------
- Tested in PLA.
- Print the tubes standing upright, tenon end down. They are plain
cylinders and need no supports.
- Print the drone foot with its socket (the wide end) facing UP.
The socket floor is then an upward-facing ledge and needs no
support.
- The forked mouthpiece is the only complex part. Take your time
with it and check that both windways are clean and open before
assembling. A thin strip of card or paper slid gently through each
windway will clear any stringing.
ASSEMBLY
--------
Each side is a stack of push-fit joints, starting from the fork:
MELODY SIDE: YFork -> Piece1 -> MelodyBody -> MelodyFoot
DRONE SIDE: YFork -> Piece1 -> DroneBody -> DroneFoot
Every joint is a tenon going into a socket EXCEPT the drone foot.
The drone foot is a sleeve that slides OVER the plain end of the
drone body.
Both feet matter for pitch. Each one adds the length that brings
its pipe down to G. Leave either one off and that pipe plays a whole
tone sharp (A instead of G).
Do not glue anything until you have played it. The push fits let
you tune (see below).
A NOTE ON JOINT FIT - PLEASE READ
---------------------------------
The joints were sized for the printer these were designed and
tested on. That printer prints outside diameters about 0.4-0.5mm
under size, so the tenons are drawn slightly oversize to make up
for it. Your printer will almost certainly be different.
- If a tenon is too tight: sand it lightly and evenly, turning the
part as you go, and test often. Do not force it. A jammed joint on
a 240mm tube gives you a lot of leverage to crack something.
- If a joint is loose: wrap the tenon with a turn or two of PTFE
(plumber's) tape, or thin paper tape, until it is snug.
- Airtight matters more than tight. A leaking joint makes the pipe
weak and breathy.
TUNING
------
The two pipes should agree on the bottom G. Play the melody pipe
with all holes covered together with the drone, and listen for
beating (a slow wobble in the sound):
- Pulling a joint out a millimetre or two makes that pipe LOWER.
- Pushing it fully home makes it as high as it will go.
Pulling out the Piece1 on either side is the easiest adjustment.
Once the two agree, you can mark the joint positions, or glue them
if you want the settings fixed for good.
PLAYING
-------
The drone has no holes. It just sounds while you play. Hold the
instrument with the melody pipe under your fingers.
The melody pipe has 4 holes. Cover them with the top hand on the
upper two holes and the bottom hand on the lower two. The wider gap
in the middle of the hole layout is normal: it is where a standard
whistle's missing hole would be.
Holes are numbered 1 to 4 from the mouthpiece end
(X = covered, O = open):
Note 1 2 3 4
---- ----------
G X X X X
A X X X O
B X X O O
D X O O O
E O O O O
Each step up the scale lifts one more finger, working from the
bottom. Blow harder with the same fingerings for the second octave.
Because the scale is pentatonic, every note fits over the G drone,
so there are no wrong notes to avoid.