MODULITH 185 Gridfinity Decor Drawers

A MODULITH Decor drawer with a full Gridfinity grid in the floor.

Same drawer, same case, same rails. The floor carries a 42mm Gridfinity grid so standard bins drop straight in, and a half-grid channel runs down the right side for the narrow stuff that never justified a whole cell. It is the same outside size as the standard 185 Decor drawer, so it swaps in for one you already have.

Four magnet slots per cell, if you want them. Every full cell takes four 6x2mm magnets so bins stay put when the drawer gets yanked open. Skip them and the drawer works exactly the same.

A tear-away front keeps it straight. A thin support panel spans the open drawer front while it prints, so even the 2H fronts come off the plate dead flat with no supports. Snap it off at the tabs when the print is done.

GEN2 is now MODULITH. Same system, same compatibility. Print only what you need, snap it together with QuickLock, and rearrange or expand your storage anytime.

WORKS WITH MODULITH 185 CASES

The Gridfinity drawer slides into any 185 case, exactly like the standard Decor drawer:

It is the same size as the standard Decor drawers, so you can mix both in one column:

FINISH IT WITH A FACEPLATE

Like every Decor drawer, the Gridfinity version takes a faceplate on the front, and you can swap styles anytime. The Classic series is free:

EdgeLabel is the most popular:

More styles: Essential · Classic Pro · Chevron

BINS THAT FIT

Any standard Gridfinity bin fits the grid. If you do not have a favourite yet, I recommend HuMa's Ultra Light Bins. They print fast and use very little filament. The Plain Edition fills the grid and the Half Grid Edition fits the side channel.

LET THE FREE PLANNER HANDLE THE DETAILS

Not sure which sizes you need? Build your layout in the free MODULITH Planner and it works out the parts for you, hands you a complete parts list with download links, and generates a step-by-step 3D assembly guide for your exact setup. Gridfinity is a toggle on any Decor drawer in your build.

👉 Open the free MODULITH Planner →

WHAT YOU'LL NEED

A MODULITH 185 case in the width you want, and a Decor faceplate in the matching size. The drawer itself needs no hardware. Some faceplate and handle styles use M3 screws, so check the faceplate page.

Magnets are optional, and there are two places they can go:

• Bin magnets: four 6x2mm per grid cell hold your bins in place.

• Soft-close: two Magnet Clips per drawer, one on the case back and one on the drawer back, each with a 10x2mm magnet. The pair pulls the drawer shut and holds it. The clips are in the GEN2 Hardware download.

• Magnets 6x2mm (paid link): Amazon

• Magnets 10x2mm (paid link): Amazon

• M3 screws, stainless (paid link): Amazon

• PETG (paid link): Amazon

• PLA (paid link): Amazon

As an Amazon Associate I earn from qualifying purchases.

SIZES IN THIS DOWNLOAD

• Widths: 1W, 2W, 3W, 4W

• Heights: 1H, 1.5H, 2H

• 12 drawers in total

The 185 grid is 4 cells deep. Across, it runs 1, 3, 5 and 7 cells for 1W through 4W, plus the half-grid channel on every size. There is no 0.5H, because a half-height drawer cannot hold a Gridfinity bin worth having.

PRINT SETTINGS

• Recommended filament: PETG, PCTG, or PLA

• Supports: None

• Perimeters: 2-3

• Nozzle: 0.4mm

• Layer height: 0.2mm

Every part is oriented ready to print.

INSTRUCTIONS

• Print the drawer as oriented, no supports

• Snap the tear-away front panel off at its tabs and discard it

• Optional: press four 6x2mm magnets into the slots of any cell you want held

• Optional: clip a Magnet Clip to the case back and one to the drawer back for a soft-close

• Attach your faceplate to the front

• Slide the drawer into the case

Full assembly instructions →

Every Gridfinity Decor Drawer in the MODULITH catalog →

SUPPORT MODULITH AND UNLOCK MORE

Join the Jerrari Club for member-exclusive models and early access. Every membership helps fund new MODULITH releases and free tools like the Planner.

NEW TO MODULITH?

🎥 Watch the system overview:

UPDATES

2026-09 - v2609, first release. Gridfinity Decor drawers for the 115, 165, 185, 240 and 270 collections, 1W through 4W in 1H, 1.5H and 2H. These replace the earlier GEN2 Decor Gridfinity Magnet Drawers, which stay available on their original pages.

Gridfinity is Zack Freedman's open-source storage system, used here under the MIT license. These drawers are licensed CC BY-NC-SA 4.0. The Non-Commercial part refers specifically to selling prints. You're absolutely welcome to use my designs in commercial environments, I actually encourage you to use them anywhere you see fit! 👍