1 / 11
NiceMCU-32S 2.8" Capacitive CYD Enclosure (with magnets) — zdjęcie 1
1 / 11

NiceMCU-32S 2.8" Capacitive CYD Enclosure (with magnets)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Will NOT fit standard CYDs. Low-profile case for the NiceMCU-32S-DEV_2.8IPS board. With 3 internal magnet recesses.

Ocena
0 / 5
Polubienia
5
Pobrania
21
Wydruki
0
Wyświetlenia
145
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Creative Commons — Attribution — Noncommercial

--!!! This case is specifically for the NiceMCU-32S 2.8" CYD !!!--

The dimensions are the same but the ports are moved around. The USB-C port is in a different spot. If there is interest in making this compatible with out boards, let me know.

I got the board on Amazon from DIYmalls here (affiliate link). The capacitive touch is super nice compared to resistive CYDs. It has low power consumption and a sensitive wifi radio, but it has a different pinout from the common ones so firmware needs to be ported. Exact same display driver though!


FEATURES
This was designed with the intention of being a highly portable case for the CYD running my port of SquachWatch -- https://squachwatch.com/. Basically a spy detector with alerts from cameras, Ring, Flock, Axon, deauthers, Airtags, etc. The original firmware is by TalkingSasquach on YouTube. Here is a link to the release video on his channel.

The magnets are for attaching it to a magsafe power bank. It obviously won't charge wirelessly, but it holds it in place while traveling. 

BOOT and RST are both accessible through the case. Also accessible are the SD card slot and USB-C port. 

The rear plate has ventilation for the SOC and a cutout for the indicator LED for anyone using opaque filament. 

PRINT SETTINGS
I printed in PETG but PLA is totally fine. I just used my default profile.

  • PETG at 250 nozzle and 70 bed, 0.4mm nozzle

  • 0.2mm layer height

  • 3 walls

  • 15% Adaptive Cubic Infill

HARDWARE (optional)
The magnets can be skipped and you could use a little glue instead of screws.

  • 4x - M3x8mm Screws (I didn't use self-tapping or heat-set inserts. It'll be fine)

  • 3x - 8 x 2mm Magnets

INSTALLATION
It's a tight fit. The order matters for getting the best fitment.

  1. Carefully align the screen over the face plate.

  2. Gently press around the edges of the board to press it into position. It's friction fit, so use even pressure along both sides.

  3. Ensure there is minimal gap between the edge of the case and the screen.

  4. Place the device face down and align the rear cover

  5. Insert the four screws. Some force will be needed to drive them in since there are no threaded inserts. Additionally, removing the screws will weaken their strength substantially once they are replaced, so I'd suggest avoiding disassembly. Your milage will vary depending on your filament and screws. 

-- *IMPORTANT* - If you need to remove the board from the enclosure, make sure to press it back out from the front. The adhesive on the screen isn't especially strong, so if you pull it out of the case from the rear, you run the risk of pulling the board right off the screen and potentially tearing the ribbon cable. Push the board out, don't pull it out.


Thanks! Be safe, have fun, pet a cat. I love you.

Tagi