1 / 6
Subaru Floor Mat Retainer Hook – J501EAJ000 / J501SAJ300 (parametric) — zdjęcie 1
1 / 6

Subaru Floor Mat Retainer Hook – J501EAJ000 / J501SAJ300 (parametric)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Printable replacement for the Subaru floor mat retainer clip (J501EAJ000 / J501SAJ300). Tested in a Subaru XV/Crosstrek

Ocena
0 / 5
Polubienia
0
Pobrania
6
Wydruki
0
Wyświetlenia
25
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
Creative Commons — Attribution — Share Alike

A printable replacement for the Subaru floor mat retainer: the hook that holds the floor mat in place, with a pin for the mat's eyelet and a clip that pushes into the hole in the car floor.

OEM part numbers: J501EAJ000 (EU) / J501SAJ300 (US)
Tested in: Subaru XV (European Crosstrek), 2014, 2.0D 147 PS. The printed part fits, clips in and holds the mat firmly.

The left and right originals are identical (not mirrored), so one model covers both sides.

Other Subaru models that use the same part number should fit too, but I have only tested the XV. Please post a make or a comment if it fits your car.

The original was hard to get and shipping it in was expensive, so I measured an original with calipers and rebuilt it as a parametric OpenSCAD model. It went through two test prints before it was "barely distinguishable" from the original.

▎ Source & full documentation: https://github.com/gira0/3d-prints/tree/main/subaru-floor-mat-retainer

Printing

- Orientation: print it on its side, exactly as the STL is saved. That way all bends lie within the layers and do not break along layer lines.
- Supports: tree supports, "on build plate only", only needed for the pin and the clip.
- Enable "Detect thin walls" in your slicer (OrcaSlicer/PrusaSlicer: Quality tab). The clip lamellae are only 0.6 mm thick and are otherwise left out. Check the slice preview.
- Brim 3–5 mm helps, because the part stands on a narrow edge.
- 0.4 mm nozzle, 0.2 mm layers, 4–5 walls. 40 % infill is enough for PLA/PETG, 100 % for TPU.

Material

- PLA+ works well for a test fit (that is what the tested part is made of). It is rigid, so the clip is tight going in: it needed a firm push with the foot, then sits very securely.
- For permanent use, print PETG, ASA or TPU. PLA softens at 55–60 °C, which a parked car easily reaches in summer.
- TPU 95A gives the flexibility of the original but grips a bit less firmly.

Customising (OpenSCAD)

bracket.scad is fully parametric. Every dimension is a named variable at the top of the file with a letter that matches the included dimension drawing (dimensions.svg). Open it in OpenSCAD and use Window → Customizer. Useful tweaks:

- Clip too tight in a rigid material: reduce clip_fin_sz (lamella size) from 6.7 to about 6.3 mm.
- Clip does not hold in your car: set clip_style = "hole" to get a screw hole instead.
- Too soft in TPU: increase the strip thickness t by 0.5–1 mm.

Transparency

I designed this with help from Claude (Anthropic's AI assistant) in Claude Code. I took all the measurements from the original part and checked every step against it and against test prints. Claude wrote and refined the OpenSCAD model from those measurements.

Tagi