Gridfinity Desk Organizer - 6 Modules + 4x3 Baseplate, Inlaid Seigaiha & Zellige Fronts (AMS)

A modular desk organizer on the 42 mm Gridfinity grid: a 4 × 3 baseplate (168 × 126 mm, it fits the A1 mini bed) and six useful modules that fill all 12 cells. Each module has a slide-in front tile with an inlaid Japanese seigaiha wave or Moroccan zellige star pattern in indigo, cream, terracotta and gold.

The feet and the baseplate pockets use the official Gridfinity dimensions, so the modules also work in any standard Gridfinity baseplate or drawer, and any standard bin works in this baseplate.

The modules

• Sticky notes (2 × 2, 35 mm tall): holds a 76 × 76 mm pad up to 20 mm thick, with finger notches on both sides.

• Small drawer (2 × 1, 42 mm tall): the drawer slides out on its own housing. Its front is set back 7 mm, so the pull handle stays inside the grid footprint. Inner space 75 × 27 × 31 mm.

• Earbuds / AirPods (2 × 1, 28 mm tall): a pocket that holds the charging case upright (up to 46 × 22 mm, with a finger scoop) and a round dish (Ø22) for loose earbuds, rings or a USB stick.

• Phone stand (2 × 1, 20 mm base): a 12 mm slot tilted back 20°, so it also takes phones in a case. The slot is open at both ends, so the phone can stand upright or sideways. There is a pointed-arch window in the backrest and a groove behind it for a pencil or stylus.

• Pen cup (1 × 1, 84 mm tall): inside 37 × 36 mm, with a chamfered rim.

• Clip tray (1 × 1, 21 mm tall): the floor curves up on every side, so you can slide clips and pins out with one finger.

Details

• Fluted side and back walls (0.6 mm V-grooves at a 3 mm pitch), a 0.6 mm chamfer on every rim, and a push-out window in each baseplate cell. A small HANMA is engraved under the baseplate and inlaid in gold on the drawer front.

• The front tiles are 1.6 mm thick. They slide down into a dovetail channel from the top, with 0.25 mm clearance on each side, and cannot fall forward. The pattern sits flush in the top 0.6 mm (3 layers), so the AMS swaps filament on only 3 layers of one thin plate. The finest inlaid line is 0.6 mm wide and the indigo gaps between colours are about 0.5 mm.

• Colours (AMS lite, 4 slots): indigo (baseplate and tile background), cream (all modules), terracotta and gold (inlays only).

Print files (Bambu Studio estimate for the A1 mini, 0.2 mm layers, no supports)

• Baseplate: 1 h 15 min, 49 g indigo.

• Modules 1 (sticky notes, earbuds, pen cup, clip tray): 4 h 00 min, 118 g cream.

• Modules 2 (phone stand, drawer housing, drawer): 2 h 28 min, 78 g cream.

• Front tiles (all 6, printed face up): 1 h 09 min, 21 g (16.2 indigo, 2.4 cream, 1.1 terracotta, 1.6 gold, including colour-change waste).

• Total: about 8 h 52 min and 265 g. The drawer housing ceiling has a 63 mm bridge between 45° chamfers, and the bridges under the Gridfinity feet are standard. Everything else is at 45° or less.

How it was checked

• Gridfinity dimensions, measured on the mesh: the foot goes from 35.60 mm at the bottom to 37.20 mm at 0.8 mm and 41.50 mm at 4.75 mm, with breaks at 0, 0.8, 2.6 and 4.75 mm. The baseplate pocket goes 36.30 → 37.70 → 42.00 mm. A foot 0.2 mm wider per side still fits (0.000 mm³) and 0.3 mm wider collides (34.5 mm³), so the clearance is the official 0.25 mm. Control: a foot 0.5 mm wider per side does not fit (174 mm³).

• Every module, with its tile (and drawer), stays inside its 41.5 / 83.5 mm footprint (0.000 mm³). All 72 neighbour pairs (6 × 6 modules, side by side and front to back) do not touch (0.000 mm³). Control: two modules 0.6 mm closer than the grid allows do collide (40.9 mm³).

• All six modules sit in the baseplate without touching it (0.000 mm³). They rest on the ridges, and a module lowered 0.3 mm would collide (281 mm³).

• Front tiles slide down their channel without touching at 5 heights (0.000 mm³). Controls: pushed 0.6 mm forward they hit the dovetail (4–23 mm³), and a tile 0.5 mm wider does not fit (11–62 mm³).

• Objects: a 160 × 75 × 8 mm phone, a 76 × 76 × 20 mm sticky-note pad, five Ø10 × 140 mm pens and a 46 × 22 × 61 mm earbuds case all fit (0.000 mm³). Controls: a 13 mm thick phone, a 78.5 mm pad, a Ø38 cup and a 49 mm case do not fit.

• The drawer slides out from 0 to 27 mm in 10 positions without touching (0.000 mm³). Controls: a drawer 0.5 mm wider per side (139 mm³) or 0.8 mm taller (24.7 mm³) collides.

• Print plates: no faces steeper than 45° (0.00 mm²) and no loose parts. The colours never overlap (0.0000 mm³). Inlay detail narrower than 0.38 mm adds up to only 0.06 mm² on the worst tile.

About this design

Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.

Español

Organizador de escritorio modular en la rejilla Gridfinity de 42 mm. Incluye una bandeja de 4 × 3 y seis módulos: notas adhesivas, cajón con tirador, auriculares, soporte de móvil, lapicero y bandeja de clips. Los frentes llevan seigaiha o zellige incrustados a 4 colores. Las cotas son las oficiales, sin soportes, y en total son unas 8 h 52 min y 265 g.

العربية

منظم مكتب معياري على شبكة Gridfinity بقياس 42 مم: قاعدة 4 × 3 وستة أجزاء، هي حامل أوراق لاصقة ودرج بمقبض ومكان للسماعات وحامل للهاتف وكوب للأقلام وصحن للمشابك. الواجهات مطعمة بنقش الموج الياباني «سيغايها» أو الزليج بأربعة ألوان. القياسات رسمية والطباعة بلا دعامات، وتستغرق نحو 8 ساعات و52 دقيقة بوزن 265 غراما.