1 / 6
Flor: Twist-to-Bloom Mechanical Lotus Ring Box (10 petals, multicolor, no supports) — zdjęcie 1
1 / 6

Flor: Twist-to-Bloom Mechanical Lotus Ring Box (10 petals, multicolor, no supports)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Twist the base ring: 10 petals open in two layers and the gold pod lifts your ring. Hidden mechanism, no supports.

Ocena
0 / 5
Polubienia
1
Pobrania
11
Wydruki
0
Wyświetlenia
40
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Home Decor
Licencja
Creative Commons — Attribution — Noncommercial — NoDerivatives

The animation (GIF) shows the real motion, rendered from the same positions that were collision-checked in code.

Flor is a mechanical lotus that blooms when you twist the ring at its base, and it is also a ring box. Closed, it is a pink-and-white bud. Turn the pink ring 150° and the ten petals open in two layers, while the gold seed pod with its stamens rises 8 mm and lifts the ring that was hidden inside. Twist back and the bud closes again.

How it works

  • The pink ring has two helical grooves inside. A 16 mm piece of 1.75 mm filament goes through the gold plunger rod and rides in those grooves. Slots in the fixed stem stop the rod from turning, so twisting the ring lifts it 8 mm.

  • Each petal is a lever. A C-shaped hook clips onto its own green axle bar on the calyx, and a side pin runs in a horizontal slot of a gold plunger fin. When the plunger rises, all ten petals swing out together.

  • The outer five petals have a 5.8 mm lever and turn 88°. The inner five have a 7.2 mm lever and turn 68°. The stroke is the same for both layers, so the petals unfold in layers and never touch each other.

  • The whole mechanism is hidden inside the calyx. From outside you only see a flower on a lily pad.

Details

  • Size: lily pad 116 × 109 mm. Flower 106 mm tall when closed, about 140 mm across when open.

  • Ring holder: a slot in the seed pod takes a ring up to about Ø21 mm outside (inner Ø17, size ~US 6.5 / EU 53) standing upright. Closed, the bud covers it: in code, only 0.08 % of sight lines from the ring reach the outside.

  • Fine details: raised petal veins 0.4 mm, 22 stamens Ø0.9 mm with anthers, 6 seed cells, sepals on the calyx and veins on the pad. "HANMA" is inlaid in gold on the small lily pad.

  • Petal colour fade: white at the base and pink at the tips, made with pink bands that get thicker as they go up (layer-height steps), so it is a gradient with only 2 filaments.

Printing (Bambu Lab A1 mini + AMS lite, PLA, 0.4 nozzle)

  • Plate 1, petals: the two layers print as two closed buds, standing up, held by 0.6 mm breakaway bridges and a 0.4 mm ring on the bed. Snap them apart with your fingers. White + pink: 3 h 17 min, 32 g.

  • Plate 2, base: lily pad with stem, calyx, twist ring, plunger head and rod. Green + gold + pink: 5 h 40 min, 79 g.

  • Total about 8 h 57 min and 110 g. No supports. All overhangs are 50° or less, except small hole ceilings and short bridges up to 3 mm wide.

  • You also need one 16 mm piece of 1.75 mm filament.

Assembly (about 10 minutes)

  1. Slide the pink ring over the stem, then press the calyx onto the stem top (D-shaped, it only fits one way).

  2. Drop the gold rod into the stem and push the gold head onto it (also D-shaped).

  3. Turn the ring until its small hole lines up with the stem slot, then push the filament piece through the hole, the stem and the rod. Turn the ring a little and the pin is locked in.

  4. Clip each petal onto its axle bar (outer and inner alternate) with its side pin entering the plunger slot. Twist to test.

How it was checked

  • 37 positions from closed to open (ring 0° to 150°): 0 collisions between the 10 petals, plunger, ring and fixed parts, with every part grown 0.15 mm (so every gap is at least 0.30 mm).

  • Controls that must fail, and do: an outer petal 2 mm longer hits its neighbours when closed. An axle bar 0.7 mm thicker (zero clearance) touches the hook. A plunger 1.6 mm out of step hits the petal pins. Removing one outer petal and its inner neighbour lets 9.3 % of sight lines reach the ring.

  • Opening: outer petals turn 88°, inner 68° (both at least 60°).

  • Print: no floating parts, colours do not overlap, and both plates fit the 175 × 175 bed.

About this design

Designed with AI assistance and checked in code before release (see above). Pictures are 3D renders and the slicer preview, not photos. Not printed yet: makes and feedback are very welcome.

Español

Loto mecánico y joyero: gira el anillo rosa de la base y el capullo se abre en dos capas de pétalos mientras el receptáculo dorado sube y te presenta el anillo. Mecanismo oculto en el cáliz, comprobado en 37 posiciones sin choques (holgura ≥ 0,3 mm), sin soportes, 4 colores AMS.

العربية

زهرة لوتس ميكانيكية وعلبة خاتم: أدر الحلقة الوردية في القاعدة فتتفتح البتلات في طبقتين ويرتفع المركز الذهبي حاملا الخاتم. الآلية مخفية داخل الكأس، وتم فحصها في 37 وضعا بلا تصادم، وتطبع بلا دعامات بأربعة ألوان.

Tagi