1 / 3
2026 RAV4 LE/SE Wireless Charger Mount Anker Zolo — zdjęcie 1
1 / 3

2026 RAV4 LE/SE Wireless Charger Mount Anker Zolo

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Clip-in Anker Zolo Qi2 charger mount for 2026 Toyota RAV4 LE/SE, with an adjustable phone stop.

Ocena
0 / 5
Polubienia
1
Pobrania
6
Wydruki
0
Wyświetlenia
114
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Automotive
Licencja
GNU General Public License v3.0

A compact wireless charger mount designed for the center console tray of the 2026 Toyota RAV4 SE, using an Anker Zolo Qi2 magnetic charger.

Developed through multiple rounds of printing and vehicle testing, this mount clips securely around the tray’s front edge. The charger is mechanically retained, allowing the phone to be placed and removed without pulling the charger out of its seat.

Features

  • Secure vehicle attachment: Two hooks wrap around the tray edge.

  • Removable charger: A screw-fastened retaining cap holds the Zolo in place.

  • Compact design: A narrow body leaves the phone’s sides accessible for easy removal.

  • Adjustable end stop: Helps position the phone, with 4 mm of total adjustment.

  • Integrated cable channel: Routes the charger cable toward the front.

  • No drilling or adhesive required.

Tested Compatibility

  • Vehicle: 2026 Toyota RAV4 SE

  • Charger: Anker Zolo Qi2, model A25M2

  • Phone: iPhone 14 Plus with a magnetic case, measuring approximately 165 × 83 mm

  • Phone orientation: Camera end facing inward, toward the dashboard

Other vehicle trims, model years, chargers, phones, and cases have not been verified. Please compare the dimensions and tray shape before printing.

Parts and Hardware

Print one of each:

  • Main body

  • Charger retaining cap

  • Adjustable phone stop

Additional hardware:

  • 5 × M3-0.5 × 10 mm socket-head screws

  • 5 × standard M3-0.5 hex nuts — approximately 5.5 mm across flats and 2.4 mm thick

  • 2.5 mm hex key

Four screws secure the charger cap; the fifth secures the adjustable stop.

Suggested Print Settings

  • Material: PETG

  • Nozzle: 0.4 mm

  • Layer height: 0.20 mm, including the first layer

  • Walls: 4

  • Infill: 40%

  • Top/bottom layers: 6

  • Scale: 100%

Main body: Print with the hook feet on the build plate and the charger opening facing upward. Supports are required beneath the tray. Allow supports to start on model surfaces, rather than limiting them to the build plate.

Retaining cap: Print with the phone-facing surface down. Designed to print without supports.

Adjustable stop: Print flat-base down. Designed to print without supports.

The retaining lip is only 0.6 mm thick. Remove any burrs carefully and avoid damaging this edge.

Assembly

  1. Remove supports and clean all mating surfaces, cable openings, and nut pockets.

  2. Insert the nuts into the underside pockets.

  3. Place the Zolo in its seat and route its cable through the front channel.

  4. Install the retaining cap. Tighten the four screws evenly until snug.

  5. Attach the adjustable stop loosely.

  6. Let the phone settle into its magnetic charging position. Adjust the stop to leave a small gap at the phone’s inner end, then tighten its screw.

  7. Check that no hardware protrudes below the vehicle-contact surface, then fit the mount to the tray.

Testing Status

V3a has been physically printed and tested for vehicle fit, secure attachment, and convenient phone placement and removal.

Long-term cabin heat exposure and extended charging performance have not yet been evaluated. Feedback from other owners is welcome.

Tagi