1 / 9
Smart scale for 5 L jugs – TAL220 + NAU7802 + XIAO ESP32-C6 (ESPHome) — zdjęcie 1
1 / 9

Smart scale for 5 L jugs – TAL220 + NAU7802 + XIAO ESP32-C6 (ESPHome)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

WiFi scale for 5 L jugs: TAL220 load cell, NAU7802 ADC, XIAO ESP32-C6, ESPHome, calibrated from Home Assistant.

Ocena
0 / 5
Polubienia
1
Pobrania
3
Wydruki
0
Wyświetlenia
29
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Electronics
Licencja
Open Community License v1.1 + General Attribution v1

A compact WiFi scale that sits under a 5 L jug and tells Home Assistant how much liquid is left, in grams and in litres. I built five of them for the nutrient jugs (Micro / Grow / Bloom / pH Down / pH Up) of my hydroponic dosing station, but it works for any liquid container up to ~190 × 130 mm footprint and ~10 kg.

One scale = one self-contained board. Load cell, 24-bit ADC and ESP32-C6 all live inside the base. One USB-C cable, nothing else. No HX711.

Features

  • TAL220 10 kg load cell in Z mounting: fixed end screwed to the base, load end under the tray

  • Adafruit NAU7802 24-bit ADC (I²C 0x2A) – measured noise ±0.12 g on the first unit

  • Seeed XIAO ESP32-C6, USB-C port flush with the outer wall on the left side: reflash or power without opening anything, and any USB-C cable fits, whatever the size of its plug

  • Closed enclosure: snap-fit lid all around, both boards held without screws

  • USB-C strain-proof: a small printed retainer clips over the XIAO and presses on its metal shield, so tugging the USB cable can't lever the board out — in any direction, lid open or closed

  • 4 neodymium magnets (19 × 9 × 4.6 mm) pressed into side slots: the scales stick to a steel shelf, side by side

  • Or screw it down: four countersunk Ø 4.5 mm holes in the floor, 100 × 70 mm spacing, symmetric

  • Ribbed TPU mat on the tray: the jug doesn't slide, and the raised rim keeps it centred

  • Calibration from Home Assistant, no reflash: zero, slope, jug tare and liquid density are persistent numbers set by buttons

  • Safe outputs: mass is unknown until calibrated, volume is unknown when the jug is removed (never a fake "0 L"), the board reboots itself if the ADC freezes

Printed parts (per scale)

File

Qty

Material

Orientation

Notes

base_ASA.stl

1

ASA / PETG

bottom on the bed

no supports

xiao_retainer_ASA.stl

1

ASA / PETG

on its side, as exported

no supports – printed on its side so the 1 mm snap tooth is drawn by the perimeters and the legs flex along the layers

lid_ASA.stl

1

ASA / PETG

roof on the bed (already flipped)

no supports

tray_ASA.stl

1

ASA / PETG

rim up

no supports

spacer_8mm_ASA.stl

1

ASA / PETG

flat

100 % infill – it carries the whole load

mat_TPU.stl

1

TPU 95A

skin on the bed, ribs up

goes into the tray ribs down

Test pieces – print these first, they take minutes and validate the critical fits on your printer:

  • test_loadcell_rail.stl – the TAL220 must sit straight against the rail

  • test_xiao_mount.stl – XIAO bed, wall slot with flush USB-C, rear stop and the retainer pockets (use it with xiao_retainer_ASA.stl)

  • test_nau7802_clips.stl – the four NAU7802 clips

  • test_magnet_slot.stl – magnet press-fit slot

Settings I use (ASA): 0.2 mm layers, 4 perimeters, 6 top/bottom layers, gyroid 40 % (spacer 100 %), bed ≥ 110 °C.
TPU: 3 perimeters, 3 top/bottom layers, gyroid 20 %, slow.

ASA because mine live in an unheated greenhouse tunnel. PETG should be fine indoors (not tested). Avoid PLA: creep under a constant 6 kg load will drift the zero.

Hardware (per scale)

  • 1 × TAL220 load cell, 10 kg

  • 1 × Adafruit NAU7802 breakout (product 4538)

  • 1 × Seeed Studio XIAO ESP32-C6 (no headers)

  • 1 × Qwiic / STEMMA QT cable 15–20 cm, one end cut to bare wires

  • 2 × M5×20 socket head screws (fixed end, from below)

  • 2 × M4×20 socket head screws (load end, from above)

  • 4 × neodymium magnets 19 × 9 × 4.6 mm (optional)

  • or 4 × Ø 4 countersunk screws, wood or M4 (optional, to screw the base down instead)

  • 1 × USB-C cable (any) + 5 V supply

  • Optional: self-adhesive u.FL FPC antenna stuck inside the lid

Wiring

From

To

Load cell red / black / white / green

NAU7802 E+ / E− / A− / A+

Qwiic red / black

XIAO 3V3 / GND

Qwiic white (SDA)

XIAO D4 (GPIO22)

Qwiic yellow (SCL)

XIAO D5 (GPIO23)

Standard Seeed XIAO pinout. Go by the position in the Qwiic connector (GND, V+, SDA, SCL), not by colour: some cables have no blue wire.

If white/green of the load cell are swapped on your batch, the slope just comes out negative: calibration absorbs it, no rewiring.

Assembly

  1. TAL220 on the fixed block, pressed against the rail, cable towards the back, 2 × M5×20 from below.

  2. Clip the NAU7802 in, wire the terminal block.

  3. Solder the Qwiic cable on the XIAO, slide its USB-C into the side hole (the end of the board goes into a slot in the wall), then lay the other end flat inside the rear stop.

  4. Push the retainer across the XIAO until both teeth click into their pockets. The soldered wires run between the board and the pockets. To remove it, spread the legs.

  5. Plug the cable into the NAU7802 and run it under the load cell through the notch at the foot of the rib, flat on the floor. No cable may touch the load cell.

  6. Check the gap between load cell and base, then snap the lid on all around.

  7. Press the magnets into their slots until they click (permanent).

  8. 8 mm spacer through the lid opening, tray on top, 2 × M4×20.

  9. TPU mat into the tray, ribs down. Check all clearances with a sheet of paper.

To reopen the lid, remove the tray first (2 M4 screws).

STEP files (Fusion 360, SolidWorks, Onshape…)

  • balance_assemblage.step – the whole scale assembled: the 6 printed parts plus simplified load cell, NAU7802, XIAO, magnets and screws, each as a named body in place

These are real B-rep solids, not converted meshes: planes, cylinders and cones are exact, so you can edit them with direct modelling (push/pull a face, change a hole diameter). A STEP never carries a feature history – the parametric source remains balance_tal220.scad.

Firmware (ESPHome)

  • balance-common.yaml – the shared firmware (comments in French)

  • balance-example.yaml – one small file per scale: name, density, antenna, API key

Printables doesn't accept .yaml files: they are uploaded as .yaml.txt — just remove the .txt.

Calibration from Home Assistant, in this order, waiting ~30 s for the raw reading to settle each time:

  1. Faire le zéro – empty tray

  2. Masse étalon – type a known mass (a water jug weighed on a kitchen scale, ~5 kg is ideal), press Enter, then Étalonner

  3. Tarer bidon vide – empty jug on the tray (optional)

  4. Densité – liquid density in g/L

Entities: mass (g), volume (L), jug present, raw reading, WiFi signal, plus the calibration numbers and buttons.

Good to know

  • Temperature drift is about ±10 g per 10 °C. Per-dose consumption (a few minutes) is accurate to the gram; day-to-day readings in an unheated space drift by tens of grams.

  • The TAL220 is rated −10 to +40 °C. Keep the jugs in the shade.

  • WiFi: the XIAO sits under a plastic lid, a few mm above a steel shelf. If the signal is poor, use the optional u.FL antenna and set antenne: ALWAYS_ON – never without the antenna plugged in.

  • The jug outline is 190 × 130 mm. Everything is parametric in balance_tal220.scad (OpenSCAD 2021+): change jug_l, jug_w, jug_r and re-export.

License

  • 3D model, OpenSCAD source and images: Open Community License v1.1 with the GAtt v1 (General Attribution) plugin. Print it, modify it, use it in your own business (a farm or greenhouse building scales for its own use is welcome) — but credit the original design, share remixes under the same license, and don't sell prints, kits or derivatives without asking me first.

  • ESPHome configuration files (balance-common.yaml, balance-example.yaml): MIT — reuse them freely in your own projects.

Tagi