MagSafe charging tray for Ford Mondeo Mk5 centre console (parametric)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
A drop-in insert that turns the right-hand console pocket into a MagSafe shelf.
- Ocena
- 0 / 5
- Polubienia
- 1
- Pobrania
- 2
- Wydruki
- 0
- Wyświetlenia
- 23
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Automotive
- Licencja
- Creative Commons — Attribution — Share Alike
What it is
The right-hand pocket of the Mondeo Mk5 centre console is a nicely shaped void that holds nothing in particular. This insert drops into it and turns it into a MagSafe charging shelf: the phone sits on the charger puck, the cable disappears into a channel, and the whole thing lifts straight back out when you want the pocket back.
Nothing is drilled, glued or taped to the car. The insert hangs on a 3 mm flange that rests on the plastic around the pocket.
Will it fit your car?
It was measured on a 2019+ facelift Mondeo Mk5 — the CD4 platform shared with the Fusion. The trim it sits in carries Ford part number KS73-F045M97-A-C-W.
Moulded interior parts vary between model years and markets, so measure your own pocket before printing the big part. The whole model is generated from a parameter block at the top of one script, so adapting it is editing numbers, not redrawing geometry. There is a measurement table in the included README telling you exactly what to measure and how.
Sized for an iPhone 15/16/17 Pro Max class phone with a 59 × 8 mm MagSafe puck. Both are parameters.
What makes it different from a generic phone cradle
The phone touches only the charger puck. The surface around the charging island is sunk 6.8 mm so the camera bump and its case lip hang in free air. Lay a Pro Max on a flat tray and it rocks on its lenses, loses magnet grip on the far side and grinds the camera glass against the print. This one holds the phone on the puck and nothing else.
The cable is genuinely hidden. A 6 mm channel runs from the puck bore, through the plate, through the wall and out through a notch in the flange. The charger's 20 mm strain relief boot has its own pocket. The cable stays below the surface for the entire run under the phone and only appears outside the phone's footprint. A second, larger exit low in the side wall is there if your car has room to route it underneath instead.
The walls match the pocket. The console pocket is not a symmetric taper — rear wall 130°, front 120°, both sides 120°, and the floor drops from 29 mm at the front to 35 mm at the rear. The insert reproduces all of it, so it sits down properly instead of wedging two millimetres in.
What you download
File | Print it? |
|---|---|
| Yes — the top half: plate, charging island, flange |
| Yes — the bottom half: the walls |
| First — 8 g test piece, checks the puck bore on your printer |
| Only if you insist on one piece — see below |
| The parametric source. FreeCAD 1.0+ |
| Source for the gauge |
| Full technical documentation |
Printing
Print the fit gauge first. Eight grams, a few minutes, and it tells you whether the puck bore comes out right on your machine before you commit to the 61 g part.
Both halves go on the bed joint-face-down. Neither needs supports. In that orientation the cross-section shrinks as it rises, so there is nothing to bridge.
The part is split for one reason: surface finish. Printed in one piece with the visible face down, the floor of the recess is a downward surface spanning 59 mm with nothing underneath. It sags into a comb of loose strands no matter how you tune supports. Split at the chamber ceiling, that same surface becomes a top surface and comes out clean. assembled.stl is included for completeness, but expect to fight it.
Use ABS or ASA, not PETG. A parked car's console gets hot enough that PETG (Tg ≈ 80 °C) starts to creep. ABS (Tg ≈ 105 °C) does not.
Set shrinkage compensation. Measured shrinkage on this geometry was 1.48 % — set Shrinkage (XY) to 101.5 % in your filament profile. Skip this and the puck bore lands about 0.9 mm undersized and the puck will not seat. This is the single most common way to get a part that looks right and does not work.
You need an enclosure. The flange is a large flat ring. Without a warm chamber the corners lift, and a lifted flange breaks the one datum the entire design depends on.
Other settings: 0.2 mm layers, 3 walls, 5 top / 5 bottom, 25 % infill, 8 mm outer brim, nozzle 250 °C, bed 100 °C, part cooling 0–10 %. About 61 g total.
Assembly
Test-fit both halves dry and put the pair in the car. The spigot holds them together without glue, so you can check flange seating, puck fit and cable routing before anything is permanent.
Bond with acetone or ABS cement. The spigot ring gives roughly 1830 mm² of joint area and an acetone weld in ABS is stronger than the material around it.
Drop the puck into the bore, lay the strain relief boot into its channel, run the cable out through the flange notch.
One quirk worth knowing
Lay the phone with the camera island towards the driver. The strain relief boot intrudes 0.5 mm into the space the camera bump wants, on the passenger side. This cannot be fixed in the geometry — the phone and the puck rise together, so raising the island changes nothing. In practice you always drop the phone the same way round, so it costs nothing; put it the other way and you will feel a slight rock.
Parametric source
The model is a FreeCAD Python script, not a hand-drawn solid. Every dimension is a named parameter, and the script checks its own work: it reports wall angles, clearances, the cable chamber height, the load on the plate under the puck at 70 °C, and it refuses to export a mesh that is not watertight or a part that has broken into two solids.
If you adapt it to another car, I would be glad to see the measurement block.