1 / 1
Lewmar Low Profile Hatch Seal Cutter — zdjęcie 1

Lewmar Low Profile Hatch Seal Cutter

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

A tool to make it easy to get a straight cut of Lewmar Low Profile Hatch Seal so you have a precise surface to join.

Ocena
0 / 5
Polubienia
0
Pobrania
1
Wydruki
0
Wyświetlenia
26
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Tools
Licencja
Creative Commons — Attribution — Noncommercial

Cutting Lewmar Low Profile Seal accurately with a 90 degree cut without distorting the seal is difficult. You can buy the seal by the foot however the complex shape makes getting a good glued joint difficult. This tool makes it much easier to get a precise cut. For the cutting tool, a utility knife with a long blade (the type you can snap segments off) is recommended. Also use a new blade although you should degrease it to prevent getting oils on the seal.

Print all the parts flat on the bed. No special strength needed.

To use it, take the two small inserts and put them into the lip of the seal on either side of where you want to make the cut. Then put that into the holder (note it has tabs that the inserts will go into) and then put the other side of the holder on. You may need to wiggle the seal around to get it to sit right. Then hold it tightly with one hand and use a gentle sawing motion to cut through the seal.

AI created README:

FINAL GASKET CUTTER — TESTED 11.5 MM INSERTS

This folder is the consolidated set to use from now on:

UpperHousing.stl Original approved top, unchanged.

LowerHousing.stl Updated bottom with the slot matching the top.

LipInsertA_11p5mm.stl Tested 11.5 mm insert A, one identification dot.

LipInsertB_11p5mm.stl Tested 11.5 mm insert B, one identification dot.

These individual STLs are exact copies of the approved versions. No 11.6 mm variants or earlier housing revisions are included.

PRINT

Print one of each in the supplied orientation, on their flat backs.

All_Four_Parts_Print_Batch.stl contains the same four parts, spaced apart, for a single print. Its footprint is approximately 148.5 x 60 mm.

Keep the slicer from placing support material in the gasket or blade slots.

FREECAD

Cutter_Assembly.FCStd contains exactly four parts in their assembly positions.

The top is translucent to make the inserts visible.

Cutter_Print_Layout.FCStd contains exactly four parts arranged on their flat backs for printing. It has no extra duplicate presentation geometry.

Cutter_Assembly.step contains the four assembled parts for other CAD software.

Both FreeCAD documents use the original top, matching-slot bottom and tested one-dot 11.5 mm inserts. Geometry is saved as editable Part shapes, not a dimension-driven feature history.

USE

Seat the two lip inserts in their locating pockets, put the gasket around them, and close the top by hand with its locating tabs engaged. The bulb remains hollow. Both housing slots open at the bulb-side edge and retain the same far-edge strip. Start the blade at that open edge and cut toward the lip, keeping your grip outside the cutting plane.

The housing blade slots are 0.6 mm wide for the 0.27 mm blade. The gap between the lip supports remains 1.2 mm. Lift the lid to remove the offcut.

VALIDATION

All four manufacturing shapes are valid single solids. The individual and combined STL meshes are watertight. Assembly interference and the blade path have been checked. The user confirmed the 11.5 mm insert fit works well.

Tagi