1 / 10
Offset Stacker for PolyDryer (exposes top port of lower box) — zdjęcie 1
1 / 10

Offset Stacker for PolyDryer (exposes top port of lower box)

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

Remix of Polymaker's PolyDryer stacker that offsets the upper box 1.5" so the lower box's top port stays accessible

Ocena
0 / 5
Polubienia
2
Pobrania
7
Wydruki
0
Wyświetlenia
48
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Kategoria
Accessories
Licencja
Creative Commons — Attribution — Noncommercial — Share Alike

This model extends Polymaker's Airlock Dock & Stacker for PolyDryer by shifting the upper box back 1.5" (38 mm), which exposes the top port on the lower box. This requires two different brackets: INWARD goes at the front (the end with the top port), and OUTWARD goes at the back, adding a shelf to support the upper box where it overhangs. Both clip onto the lid of the lower box the same way the original does. The upper box's edge ends up about 0.5" past the port center, leaving room for the PTFE tube to bend upward.

Why offset? With the original stacker, the upper box sits directly over the lower box's top port, so a tube has to bend sharply sideways as it leaves the port. That works with the 6 mm OD tube that comes with the PolyDryer, which fits the stock rubber gasket. But if you want 4 mm OD PTFE all the way from the box to the printer, you need a push-to-connect PC4-M10 fitting at the port instead (I used this adapter: https://www.printables.com/model/1463512-parametric-polymaker-polydryer-pneumatic-fitting-a), and that needs room to stick straight up. Offsetting the upper box leaves the port open, so the fitting fits and the tube can curve gently upward.

Stacking options

Each box that has another box on top of it needs one INWARD and one OUTWARD bracket. A two-box stack is about 11" deep at the top, compared with 9.25" for a PolyDryer box alone; the footprint on the bench doesn't change.

I tried two kinds of triple stacks. Offsetting each box further in the same direction (a "ziggurat") is a bit unstable, and I wouldn't trust it if the upper boxes hold much more filament than the bottom one. Alternating the offset direction (a "zig-zag") feels solid: the third box sits directly over the first, and the middle box has to be turned around so its port is on the opposite end, but PTFE tubing is flexible enough to route around both. Either way, a three-box stack is tall and narrow, so I'd anchor it to a wall or shelf.

That said, it's simplest to stick with double stacks, either side by side or as a mirrored pair (two stacks front to front with their upper boxes offset outward). A mirrored pair is about 22" deep and puts all four ports within a few inches of each other near the middle, which works nicely for four-toolhead setups that expect all spools on one side: four PTFE tubes rise in a fairly tight column.

Printing Considerations

Both models print without supports. The files are already oriented for printing; in particular, OUTWARD is rotated 45° on purpose, so don't lay it flat. OUTWARD may need a brim if you have bed adhesion issues, although I printed mine without one.

I used PolyLite PETG on a Prusa CORE One (0.4 mm nozzle, 0.2 mm layers, 2 perimeters, satin PEI build plate). In principle PLA should work as well.

Design Notes

The original model's airlock storage (the oval cutouts that hold the box's two airlocks while it dries) still works on the INWARD bracket. On the OUTWARD bracket the oval is only there to match the original's shape. The shelf and braces get in the way, and I couldn't find a spot on that part where an airlock would stay put.

The INWARD bracket was revised after one of the original’s arms snapped off at its narrow joint during a filament swap: each arm now stays full width down to the frame, with a curved shoulder tying it in, roughly doubling the material at the joint. If you printed the earlier version, it’s worth reprinting, just to have on-hand if/when the original breaks.

Claude (an AI assistant) was used to modify Polymaker's original model, but the design requirements, test prints, and fit corrections were mine (e.g., adding a relief pocket after a test print showed the INWARD bracket rubbing against the lid's raised edge, and reinforcing the INWARD arms after one broke in use). All files shown have been printed and tested on actual PolyDryer boxes.

Tagi