1 / 8
HTD 3M Pulley 40T & 60T, 5 mm D-Flat Bore – Printed & Tested — zdjęcie 1
1 / 8

HTD 3M Pulley 40T & 60T, 5 mm D-Flat Bore – Printed & Tested

Zamów wydruk tego modelu

Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.

Zapisane na tym urządzeniu.

HTD 3M pulleys, 40 and 60 teeth, 5 mm D-flat bores, printed and run on a 315-3M belt. STL + STEP. Any size free online.

Ocena
0 / 5
Polubienia
3
Pobrania
14
Wydruki
0
Wyświetlenia
60
Oceny
0

Aktualizacja u źródła:

Informacje o modelu

Źródło
Printables
Licencja
Creative Commons — Attribution

An HTD 3M timing pulley pair, 40 and 60 teeth, printed and run on an HTD 315-3M belt. Both 5 mm bores carry a D-flat under one M4 set screw in a captured nut, the 60-tooth pulley runs on six spokes, and both print their flanges in place.

Printing

  • Printed on an Anycubic Kobra 2 Max in PETG, 0.15 mm layer height.

  • Print the "-w-supports" STLs. Breakaway supports hold each top flange, which prints in place; snap them off after printing.

  • Push an M4 nut into each hub's slot; the set screw closes on the shaft's flat.

  • The STLs are exactly what was printed for the photos: pulley 1 with 0.2 mm of print compensation, pulley 2 with none. The STEP file is nominal size.

Files

  • STEP at true size: one file with every part of the drive, the belt included.

  • STL for printing:

    • HTD-3M-40T.stl - pulley 1, 40 teeth, without supports

    • HTD-3M-60T-P2.stl - pulley 2, 60 teeth, without supports

    • HTD-3M-40T-w-supports.stl - pulley 1 with breakaway supports under its top flange: print this one

    • HTD-3M-60T-P2-w-supports.stl - pulley 2 with breakaway supports under its top flange: print this one

Need another size?

These were designed in the CheapCADTools Timing Pulley Generator. Open this exact design there and change the teeth, bore, hub, set screws, spokes or flanges, or switch to any of 34 belt profiles (GT2, HTD, T5, AT5, XL, MXL and more): https://cheapcadtools.com/samples/htd-3m-40t-60t-printed-d-flat-six-spoke-pulleys/?ref=printables

Belt length for your centre distance, free: https://cheapcadtools.com/belt-length-calculator/?profile=HTD%7C3M&z1=40&z2=60&n=105&ref=printables

Paid, so you know: designing in the generator is free; downloading a new STL, STEP, DXF or SVG from it costs tokens (an STL is 3 tokens, about 15 cents). The files on this page are free.

All settings, as designed

Drive

  • Family: HTD; Pitch: 3M

  • Belt Height (mm): 10; Clearance Height (mm): 2

  • Centre Distance (mm): 81.94 (belt 105 teeth)

Pulley 1

  • Num. Teeth: 40; Bore Diameter (mm): 5; Flat Depth (mm): 0.5

  • 3D Print Compensation (mm): 0.2; Tooth Clearance: Standard; Backlash: Standard

  • Hub OD (mm): 20; Hub Height (mm): 10

  • Retention Method: Set Screw (captured nut); Set Screw Size: M4; Number of Screws: 1

  • Flanges, 3D Print: Flange Height (mm) 3; Flange Angle (°) 15; Rim Radius (mm) 4; Top flange as separate part: no

  • Add Print Supports: Nozzle Dia. (mm) 0.4; Max Spacing (mm) 10; Air Gap (mm) 0.2

Pulley 2

  • Num. Teeth: 60; Bore Diameter (mm): 5; Flat Depth (mm): 0.5

  • 3D Print Compensation (mm): 0; Tooth Clearance: Standard; Backlash: Standard

  • Hub OD (mm): 20; Hub Height (mm): 10

  • Retention Method: Set Screw (captured nut); Set Screw Size: M4; Number of Screws: 1

  • Spokes: Spoke Count 6; Spoke Width (mm) 5; Hub OD (mm) 20; Rim Depth (mm) 5; Fillet Tip (mm) 3; Fillet Base (mm) 4; Spoke Height (mm) 8

  • Flanges, 3D Print: Flange Height (mm) 3; Flange Angle (°) 15; Rim Radius (mm) 4; Top flange as separate part: no

  • Add Print Supports: Nozzle Dia. (mm) 0.4; Max Spacing (mm) 10; Air Gap (mm) 0.2

Licence: CC BY 4.0. Credit "CheapCADTools" when you share it.

Tagi