GT2 Pulley 30T & 45T, 5 mm Bore – Printed & Tested (STL + STEP)
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
GT2 pulleys, 30 and 45 teeth, 5 mm bores, printed and run on a real belt. STL + STEP. Any size: free to design online.
- Ocena
- 0 / 5
- Polubienia
- 0
- Pobrania
- 5
- Wydruki
- 0
- Wyświetlenia
- 40
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Mechanical Parts
- Licencja
- Creative Commons — Attribution
A GT2 timing pulley pair, 30 and 45 teeth on 5 mm bores, printed and run on a GT2 belt. The 45-tooth pulley is cut down to three spokes on a 1 mm web, both print their flanges in place on breakaway supports, and two M3 set screws per hub bite into captured nuts.
Printing
Printed on an Anycubic Kobra 2 Max in PETG, 0.15 mm layer height.
Print the "-w-supports" STLs. Breakaway supports hold each top flange, which prints in place; snap them off after printing.
Push an M3 nut into each slot in the hub and turn the M3 set screws in against the shaft.
The STLs are exactly what was printed for the photos: pulley 1 with 0.2 mm of print compensation, pulley 2 with none. The STEP file is nominal size.
Files
STEP at true size: one file with every part of the drive, the belt included.
STL for printing:
GT-2M-30T.stl - pulley 1, 30 teeth, without supports
GT-2M-45T-P2.stl - pulley 2, 45 teeth, without supports
GT-2M-30T-w-supports.stl - pulley 1 with breakaway supports under its top flange: print this one
GT-2M-45T-P2-w-supports.stl - pulley 2 with breakaway supports under its top flange: print this one
Need another size?
These were designed in the CheapCADTools Timing Pulley Generator. Open this exact design there and change the teeth, bore, hub, set screws, spokes or flanges, or switch to any of 34 belt profiles (GT2, HTD, T5, AT5, XL, MXL and more): https://cheapcadtools.com/samples/gt2-30t-45t-printed-three-spoke-pulleys/?ref=printables
Belt length for your centre distance, free: https://cheapcadtools.com/belt-length-calculator/?profile=GT%7C2M&z1=30&z2=45&n=100&ref=printables
Paid, so you know: designing in the generator is free; downloading a new STL, STEP, DXF or SVG from it costs tokens (an STL is 3 tokens, about 15 cents). The files on this page are free.
All settings, as designed
Drive
Family: GT; Pitch: 2M
Belt Height (mm): 5.5; Clearance Height (mm): 1
Centre Distance (mm): 62.32 (belt 100 teeth)
Pulley 1
Num. Teeth: 30; Bore Diameter (mm): 5
3D Print Compensation (mm): 0.2; Tooth Clearance: Standard; Backlash: Standard
Hub OD (mm): 20; Hub Height (mm): 6
Retention Method: Set Screw (captured nut); Set Screw Size: M3; Number of Screws: 2
Flanges, 3D Print: Flange Height (mm) 2; Flange Angle (°) 15; Rim Radius (mm) 3; Top flange as separate part: no
Add Print Supports: Nozzle Dia. (mm) 0.4; Max Spacing (mm) 10; Air Gap (mm) 0.2
Pulley 2
Num. Teeth: 45; Bore Diameter (mm): 5
3D Print Compensation (mm): 0; Tooth Clearance: Standard; Backlash: Standard
Hub OD (mm): 13.35; Hub Height (mm): 10
Retention Method: Set Screw (captured nut); Set Screw Size: M3; Number of Screws: 2
Spokes: Spoke Count 3; Spoke Width (mm) 6.55; Hub OD (mm) 13.35; Rim Depth (mm) 3; Fillet Tip (mm) 1; Fillet Base (mm) 2.5; Spoke Height (mm) 1
Flanges, 3D Print: Flange Height (mm) 2; Flange Angle (°) 15; Rim Radius (mm) 3; Top flange as separate part: no
Add Print Supports: Nozzle Dia. (mm) 0.4; Max Spacing (mm) 10; Air Gap (mm) 0.2
Licence: CC BY 4.0. Credit "CheapCADTools" when you share it.
