Coping Saw Holder for 1/4" Pegboard – Drop In, Lift Out
Obliczymy ostateczną cenę na podstawie wybranego pliku. Sprawdzisz ją i zaakceptujesz przed płatnością.
Zapisane na tym urządzeniu.
Hangs a coping saw by its frame on standard 1/4" pegboard. Drop the saw in from the top and lift it straight out.
- Ocena
- 0 / 5
- Polubienia
- 5
- Pobrania
- 7
- Wydruki
- 0
- Wyświetlenia
- 25
- Oceny
- 0
Aktualizacja u źródła:
Informacje o modelu
- Źródło
- Printables
- Kategoria
- Organizers
- Licencja
- Creative Commons — Attribution — Noncommercial
A coping saw takes up a lot of space lying flat
The frame is a big open loop with a thin blade strung across it, so a coping saw lying flat on a shelf or bench takes up far more room than its size suggests. I couldn't find a pegboard holder made for one, so I made this.
The top bar of the frame drops into the holder, so the frame sticks straight out from the board and the blade hangs straight down beside it. It goes in and comes out with one hand.
How it works
Drop in from the top: the top bar of the frame drops into the channel along the top of the holder. It comes out through the rounded notch at the end, where the frame bends down.
The blade end sits in a pocket: the front of the frame, where the blade is clamped, sits in a pocket inside the holder. The blade comes out through a narrow slot in the bottom.
Blade faces the board, for safety: the saw hangs with its blade toward the pegboard, so you don't brush against the teeth when you reach past it.
Lift out: lift the saw straight up and it's free. To put it back, drop the top bar into the channel.
How it hangs
It uses the same printed screw as my Magnetic Chisel Holder and my other pegboard holders. The screws go into the board first and the heads stay out. The holder hangs on them.
Grips the hole: the special 1/4"-20 thread is slightly oversize, so it bites into the edge of the pegboard hole and holds tight.
Self-centering: a tapered tip drops into the hole and centers the screw as you start it.
Flat-blade drive: the head has a slot for an ordinary flat-head screwdriver.
Locks the holder on: the underside of the head is a cone. The keyhole slots on the back have tapered lips that fit that cone, so the holder can't pull away from the board.
Pegboard compatibility
Standard pegboard with 1/4" (6.35 mm) holes on 1" (25.4 mm) spacing
Tested on 3/16" (4.8 mm) thick pegboard
Not for IKEA Skådis or other slotted boards
Dimensions
Holder: 1.6" wide × 3.5" tall (40.6 × 88.9 mm)
Sticks out from the board: 2.44" (62.0 mm)
The STEP file is included if your saw's frame needs a wider channel.
Print settings
PrusaSlicer estimates 2 h 17 min and 52 g of PETG for the holder on my Original Prusa i3 MK3S (screenshot in the gallery). The two printed screws are extra. I printed mine in white PETG. My PrusaSlicer config file is included.
Printer: Original Prusa i3 MK3S, 0.4 mm nozzle
Slicer profile: 0.30mm DRAFT @MK3 (PrusaSlicer 2.9.6)
Material: Generic PETG, 240 °C nozzle; 85 °C bed for the first layer and 90 °C after
Layer height: 0.3 mm (0.2 mm first layer)
Perimeters: 2
Infill: 15% grid
Top / bottom solid layers: 4 / 3
Supports: none
Brim: none
Orientation: as in the screenshot. The STL is already in print orientation.
About that saw
Yes, that's rust. My coping saw looked perfectly fine hanging in the shop. Then I put it next to a fresh white print, turned on the lights and pointed a camera at it. Photography is the great revealer.
The holder works just as well with a clean saw. Mine is getting steel wool and a coat of paste wax, eventually. Probably.
More pegboard holders with the same screws
Magnetic Chisel Holder for 1/4" Pegboard – Holds 3, Fits Any Brand
Magnetic Tool Holder Bar for 1/4" Pegboard – 13 Snap-In Magnets, No Glue
Tilt-Out Screwdriver Holder for 1/4" Pegboard – Expandable, No Hardware
Epoxy & Glue Bottle Holder for 1/4" Pegboard – With 4 Mixing Trays
Swing-Out Screwdriver Arm for 1/4" Pegboard – No Headroom Needed
Screw-In Pegboard Holder for 1/4" Driver Set Case – Won't Fall Off
If you print one, please post a Make. Bonus points if your saw is rustier than mine.