Liczymy pasujące modele…
Mount an IR interruptor sensor at car bumper height. The sensor will turn on a lamp when IR beam blocked. Used for backing into the garage so the bumper will clear the garage door. Back the car in until the lamp turns off. The 3D part…
Hotwheel Display Garage A Garage Display where you can put your 1:64 model cars in and mount it on the wall. How to Assemble: Take the connection pieces and insert them into the holes of the Display Garage so that they stay together. How…
Summary This is a easy-to-print 1:24 scale model of a oil drum / oil barrel. Print Print with 0.2 layer hight or lower. No supports are needed. Use 3 perimeters and 10% infill. Dimensions at 100% scale (1:24) Height: 36.6mm Diameter:…
Warning!! You may need to change the orientation of your models to print The containers can be stacked on top of each other and are very stable. They have special grooves so that you can adjust their size and purpose, just insert…
This is my version of a hinged holder for the Aqara door and window sensor to be mounted on a garage door. It uses a piece of 1.75mm filament as hinge pin. I made the clearances fairly large to ensure easy swing since the magnet is quite…
Ich habe eine Halterung für eine Fernbedienung der Marke Marantec Digital 572 erstellt. Sie kann an der Sonnenblende befestigt werden. Ich empfehle mit PETG, ABS oder ASA zu drucken, da es im Auto sehr warm werden kann und PLA sich sehr…
Remixed the original clip as I didn't want to have to attach anything to the remote and as I still had the original Steel Line Garage remote holder I made modification to make the clip narrow and able to slide into the remote holder.
This modular garage is designed for Hot Wheels and other 1:64 scale cars. ✔ Expandable – stack as many levels as you want ✔ Separate floor and roof parts available (uploaded separately) ✔ Perfect for collectors who want to display their…
This is the base plate for the modular Hot Wheels garage system. ✔ Designed for Hot Wheels and other 1:64 scale cars ✔ Works with the modular garage structure ✔ Allows you to start building your garage from the ground up ✔ Combine with…
This is Version 2 of the expandable Hot Wheels garage module. ✔ Improved stability and design ✔ Stackable – compatible with base and roof ✔ Works with Version 1 modules ✔ Fits standard 1:64 Hot Wheels and other die-cast cars You can…
I found it difficult to pull down the door as the handle was flush with the frame. So i extended it by another 3mm. Also i extended the back blocker to the full length of the handle in effort to keep it somewhat straight. I printed this…
I recommend printing in the orientations shown in 3rd picture, with a large brim to keep the edges from pulling up off the bed-plate. No supports necessary, but brims are highly encouraged. This is modular so it can be used with just the…
A simple tool designed to help make painting eyes on garage kits easier, more comfortable, and more dust-free. Simply choose the hole size that is closest to the peg of the piece, then insert along with some blue tack or clay to get the…
Attaches a garage door remote to a car sunscreen. Measurements Remote space: 1.38cm deep 5.7cm wide My garage door remote is around 1.4cm thick, but I've made this 2mm smaller to create a tight fit. Open on both ends, so a longer object…
Hier eine simple Garage für Hotwheels Autos. Die Teile werden einzeln gedruckt und zusammen geklebt. Daher kein AMS nötig. Ohne Support.
Beschreibung Dieser Spraydosen-Halter wurde entwickelt, um Ordnung in das Chaos von Lack-, Reinigungs- und Schmiermitteldosen zu bringen – ohne wackelige Regale, ohne Umkippen und ohne Gefummel. Das System besteht aus einzelnen,…
Holes added to curved part to allow for access for set screw tightening if so inclined.
Just a simple hut for the Gerbil to hang out in. Cookie the Gerbil loves it! Use supports for the top of the dome. Organic gave me the best material usage.
Heavy-Duty Garage Shelf Hook (60lb+ Capacity) Looking for a way to declutter your garage or workshop? This heavy-duty hook is designed specifically for standard garage shelving units, providing a rock-solid mounting point for your…
Wall mount for Tuya Zigbee Garage Door Receiver, https://www.aliexpress.com/item/1005005622553564.html . Should be a press fit for easy insertion and removal. Wiring: Connect one wire to NC (normally closed) and the other wire to NO…
I made these hooks that can be used to hang many different objects on the wall. I printed these in PETG and currently use it to hold outdoor Dewalt tools, a foldable table, and other tools. HD indicates it's heavier duty.
A simple Parking Garage playset model for use with toy cars.
This is a LEGO Compatible 16-stud Garage Door, it is a little thicker and has a middle hinge for stability.
A clip that mounts on the handlebars of your motorcycle to hold a Gliderol garage door opener. So much more convenient than stopping and looking for the opener. Just click it from your handlebars on the way into the driveway. Suits 25mm…
A cover to go over the top of the gliderol garage remote holder mount. Designed primarily to be used in conjunction with my garage remote holder handlebar mount so it's not so obvious sitting on your handlebars. You can still operate the…
A clip to hold a Gliderol garage door opener that you can stick on your car console, door jamb, garage wall etc. to keep your remote opener handy. Designed for a snug fit using a scan of a remote
Here is a simple but very cute way to enjoy St Patricks Day with everyone. Very simple design but very festive for your outdoors. This was my wife's idea and it turned out great. To attach it the garage door we use “DIYMAG Adhesive…
Ablagefach passend für das Fach in der Mittelkonsole eines BMW E60 bzw. E61. Einmal als Blanko-Variante um selbst ein gewünschtes Fach bzw. eine spezielle Form zu integrieren. Einmal mein aktuell genutztes Modell, einmal 3 Münzfächer,…
A Protechtor to safe your cars tailgate from being damaged by hitting the garage door rail. It Simply Clips onto the Rail. No Glue No Screws needed! It doesnt affect yor Garage Door at all. Its Designed to Fit the Bigger Part of The Rail…
This is a slide-in housing for the LiftMaster 373LM garage door remote. This mount is designed to be adhered to a vehicle surface so that you can use a strong, heat resistant double-sided tape. Before this I was using adhesive…
Original model I remixed was a great setup. Thankfully the onshape design was provided, I was able to use that as a basis, to recreate in a parametric format. It is now able to be have differnt shapes and combinations. Including being…
Make sure you have "Bridge direction" set to 45 deg so that there are no long bridges. Mirror the side to get opposite one. Holes are meant for alignment while gluing, the fit filament pieces. I used 20mm standard profile with PLA.…
After one of the plastic exterior handles on my garage door broke I decided to try and design my own and 3D print. The original one is injection molded, very rigid any shiny and likely made from Glass-Filled Nylon (PA-GF). So after…
This lets you mount a myQ garage door remote (model L993M) to the wall. There are two versions. One uses separate top and bottom pieces that snap together with twelve 2x1 mm magnets on each side. The other is a single solid model meant to…
This model is a detailed representation of a classic V-twin engine, originally created as a gift for a professional mechanic. It features a rugged, industrial design complete with a motor oil can and a mounted tire accent. The model…
This is for an older Gladiator Garageworks tool chest (that I don't think they sell any more) If you want to make different versions of the trays, use the generator with the following padding. The left and right padding is 10mm, and the…
Handvat voor een garagepoort voor een bout van 4.88mm met trektouw. Groetjes ludo Handle for a garage door for a 4.88mm bolt with pull rope. Regards, ludo Manilla para puerta de garaje con pestillo de 4,88 mm y cuerda de tracción.…
Modular Scale Garage Diorama with Adjustable 2-Post Lift Elevate your diecast display with this highly detailed, professional-grade garage diorama. Designed specifically for 1:18 and 1:24 scale models , this set provides a realistic…
A mount for the YoLink Finger and Genie Garage Door Opener. I wanted to have a easily movable mount for the YoLink Finger for my Genie Garage Door. Created this to allow me to move the mount anywhere that the Garage Door Opener could…
For the gate control that was always broken.
Upgrade your garage wall button with this mechanical switch conversion. Instead of a cheap plastic doorbell-style button, this uses standard Cherry MX-compatible switches to trigger your garage door opener. Mechanism : This is a wired…
Fairly simple duct that sits on the sill of my garage door and lets me attach a 4-inch hos for ventilation. Prints without supports if you lay it vent side down. Holes are countersunk for #8 wood screws.
🚗 Garage Parking Assistant Laser-guided LED parking helper for tight garages Never hit the wall again. This DIY parking assistant helps you stop in the perfect position every time when entering a small or tight garage. Using a laser…
A small clip-in holder for cheap chinese garage door remotes. Print with PETG or other low-creep material.
This is a very satisfying model to use. The opener snaps firmly into place. Although it was designed with the intention of mounting it as shown in the photos, the friend I made this for didn't like the upside-down lettering so he mounted…
Changelog V1.2 Revised dimensions of upper main gate trim so you dont have to cut it to lenght V1.2 Added roof to garage Overview I've created miniature garage siutable for storing hot wheels. Project doesn't require you to have any fancy…
This is a case for a cheap, thin 433Mhz remote control duplicator that can be found in pages like AliExpress (see the attached picture if the link doesn't work). To install, follow these instructions: Insert the button from the inside of…
GR-Wall: Modular Garage Wall Track System Stop drilling a new hole in the wall for every single tool! GR-Wall is a complete modular ecosystem designed for maximum strength, flexibility, and a clean garage organization. The entire system…
A simple print in place hinge to use the Ikea Myggbett door/window sensor as a garage door sensor. Other than a couple strips of double sided tape, no extra hardware is required. The sensor clips onto the hinge, so the original base is no…
🧩 Komponenten Für den Zusammenbau werden folgende Teile benötigt: 🔘 2× Rillenkugellager 693 ZZ (3×8×4 mm) 📡 Magnetsensor-Modul (siehe Link unten) 🔩 Optional: Schrauben zur Befestigung am Tor Sensor (Beispiel):…
Create your own space with this bold “Man Cave” sign. Perfect for garages, game rooms, or personal hangouts, this 3D printed sign adds a clean and modern touch to any man cave setup. A great gift for dads, husbands, or anyone who enjoys…
Print in TPU for the rubber feel. Change infill and wall layers depending on required softness or stiffness. Concept is not printed yet. Support might not be needed, depending on print pattern. 2mm width of each web. I have to test print…
I wanted a way to monitor my garage doors in Home Assistant and created this simple hinged model to mount high on the door as a self-contained unit. Prints without supports (you may have to flip the sensor side 180 degrees to make it flat…
Prints best detail on resin. But can be FDM printed also. Side cabinets included as a separate file also.
Intended to be hung from the ceiling of a garage by a piece of fishing line (or similar) a few inches from the top of a vehicle's windshield to mark a consistent parking depth. Can be used either to make sure a vehicle is pulled in far…
Eng : A Garage Table Model The Measures Will Come With Updates In The Feature Model Phase: v.0.1 Pl : Model Stołu Garażowego Wymiary Przyjdą W Przyszłości Razem Z Aktualizacjami Modelu Faza Modelu: v.0.1
I’m sharing one of my older projects: modular, fully customizable storage and display boxes designed for small die‑cast vehicles. Each unit connects to the next, allowing you to build anything from a single cube to a full wall‑mounted…
I purchased a garage door opener and the 2 remotes only came with 1 clip. I could buy another clip, but where's the fun in that? I printed this clip to fit over the 3mm thick side in my glove box. I used Inland Nylon to resist the heat in…
Introducing this innovative mountable Swatch board holder, designed specifically for standard garage shelf pillars. This versatile and practical box offers an efficient solution for organising and storing your swatch boards. Features : •…
Low guide shoe for side sectional door for garage door. It provides ground guidance for any laterally moving wooden or PVC door. For specific dimensions, please contact me via private message. Can be printable with PLA or PETG Print…
Small remix to allow mounting a Shelly Blu adapter on the rail of a Hormann automatic garage door. I've made sure it sucks out a bit at one side, so that the driving train of the door can still pass the sensor. In combination with a…
Ich habe 2 Stützen für die Tut Tut Flitzer Parkgarage als Ersatz konstruiert um sie zu ersetzen. Beide sind im Erdgeschoss verbaut.
Selbstbau einer Mähroboter Garage (Carport) für weniger als 20€ Materialkosten. Die Garage ist für den WORX Landroid WR165E und ähnliche Modelle zugeschnitten. Eine Anpassung für Roboter Modelle anderer Hersteller ist leicht möglich. Für…
Tesla stopped including the Homelink garage door opener with their Model Y/3 cars. I found a very nice, small remote control (Xinda Remote Control Duplicator, only about 1.5"x2.5") on Amazon and created this holder for it. It clips onto…
These clips suit the RackIT 400kg racking System from bunnings. They're designed to clip to the braces on the vertical stands, found here. The models here are made to fit the cross braces as shown in pictures but for a bit more storage i…
Print two of these in strong weather resistant filament. Hook them first and swing them around underneath the top part of the garage unto the tongue/grove to secure. Update, Shim-5 is a 5 deg shim that gets the garage a bit closer to the…
I wanted our garage door remote that stays in the house to look more like a fixture. This case turns the Genie G3T-R Garage Door Opener into a wall-mountable button. Use #6 or #8 screws to mount it or glue MagnetAddon.stl to the base and…
A magnetic hook which just slots in nicely into a standard garage shelf with ~10.5 mm large hole and ~5.4 mm small hole. The hook was designed with printability in mind so the layer lines are perpendicular to the load bearing part, so…
UPDATE : I expanded the I expanded the hole for the nut to fit amazon ordered nuts. Also added an expanded base hole (40mm) for my larger shovel handle on one of the files I added. Working Nuts for this model:…
Created this for my mower. Printed it with 15% infill it is very stable. For "glas" i took regular "acrylic glass film". You have to cut the parts with slicer to the size of your printer. After printing you have to glue them together with…
Clicker case to mount on vehicles, made for a 3 door garage door setup at work.
Add an M600 colour change for the lettering if you want. Push fit MX switch. Need to supply your own keycap. Or print one.
With the garage door insulation kit shown in the pictures, one clip gets bonded to the door, and the other engages it after being pushed through a hole in the insulation. The clips supplied in the kit can warp over time and disengage to…
My garage door has a T handle on the front that, when turned, extends arms on the door into square holes on the garage door rails, locking the door in place. The garage door opener doesn't know this, though, and will still try and open…
Replacement button for a Novoferm garage door remote. Button shape: ellipse Ellipse dimensions: 8.4mm x 4.7mm Lip thickness: 1mm Total thickness: 4mm
Garage door remote holder for motorcycle handlebars (22mm.)
Use this to attach your hub to your garage door opener with 3M tape while still being able to easily remove it. If you live in a hotter climate, print in PETG, ABS, PC, or some other higer temperature filament.
Garage Door Opener on a Bicycle at MKE Gadgets #210 In this video, a client asked me to attach a garage door opener to his bicycle handlebar. The door opener used in this video Universal by Chamberlain available at most super ultra mega…
This attachemend could used via IoBroker, A-Echo, zigbee Hub.. see Amazon Open and Close Position are tracked because the magnet travels on the sled! Nice to switch Zigbee LED Stribes when Door is open/close/drives. Send Messages,…
Likely a very basic use of the P1S but it is a functional problem that we were able to solve. Background Recently upgraded Two (2), side-by-side Garage Door Openers. Also have a garage parking assistant. Long story, short, the parking…
this model is a perfect fit for your layout easy to print on a small 3D printer. hollow so you can light it up with some lights! Have fun and leave a like if you like it and commit if you want me the make any other buildings. Thanks!
Garagedoor for the fireman sam station. Fits as original Print with minimal supports for the hinge pins.
There are two variants, one with 3mm hole and one with a 4 mm hole. Look at your rope to decide which one you will need.
A few screws are needed for assembly, as shown in the picture. A good location to mount them is in a utility room or garage.
I've been looking for a clip for a garage door remote for a long time, but I couldn't find anything. I had to make my own version for a popular remote. For remotes known as Universal 4 Buttons Garage Door Opener Remote Control 433MHZ
